NF F31112en鐵路車輛.對涂鴉的防護
《NF F31112en鐵路車輛.對涂鴉的防護》由會員分享,可在線閱讀,更多相關《NF F31112en鐵路車輛.對涂鴉的防護(10頁珍藏版)》請?jiān)谘b配圖網上搜索。
1、 NF F 31-112 French Standard December 1994 Classification Number: F 31-112 Railway rolling stock Anti-graffiti protection Test procedures and methods for evaluating the behaviour of the materials and graffiti removal products. F: Matriel roulant ferroviaire – Protection vis--vis des gra
2、ffiti – Procdures d’essais et mthodes d’valuation du comportement des matriaux et des produits d’limination E : Railway rolling stock — Protection in relation to graffiti — Tests procedures and methods of valuation, behaviour of materials and products of expulsion D: Schienenfahrzeuge — Graffit
3、ischutz — Prfungsverfahren und Bewertungsmethode des Werkstoffverhaltens und der Beseitigungsverbindungen French Standard approved by a decision of the General Director of afnor on 20 November 1994 to become effective as of 20 December 1994. correspondence On the date of publication of thi
4、s document, no draft standards or European or International standards are known to exist on the same subject. analysis This document describes the testing procedures and methods for evaluating the behaviour of the materials and products for removing graffit. descriptors Technical International The
5、saurus: railway equipment, railway rolling stock, protection, stain, paint, ink, test, protective product, cleaning, effectiveness, colorimetry, colorimetric deviation modifications corrections Published and distributed by the French Standardization Association (afnor), tour europe cedex 7 92049
6、 paris la dfense — tel. : (1) 42 91 55 55 Prepared by the BNCF (Railways Standardization Bureau) – 15 rue Traversire – 75571 Paris Cedex 12— tl. : (1) 40 19 15 03 Contents Page Foreword 3 1 Field of application 3 2 Normative References 3 3 General principle 3 4 Preparation of test spe
7、cimens 4 5 Graffito application 4 6 Graffito elimination procedure 5 7 Aggressivity test 5 8 Effectiveness test 6 9 Evaluation of aggressivity and effectiveness 8 10 “G” grading of the material 8 Appendix A (normative) Type test specimen 9 Appendix B ( informative) Presentation
8、 of colorimetric deviations 10 Foreword This document has been prepared by an ad hoc working group of the “Comfort” standardization commission CN CF 103 . 1 Field of application This document describes with regard to railway rolling stock: — the test procedures; — the laboratory methods for
9、evaluating the results, in order to grade impermeable materials in new condition and graffiti removal products. It does not concern textiles or throwaway products. These materials and products may be the subject of particular standards. 2 Normative References This document contains the provisio
10、ns of other publications in dated or undated references. These normative references are given at appropriate points of the text and in the publications listed below. With regard to dated references, any amendments or revisions to a publication will only apply to this document if incorporated into i
11、t by amendment or revision. With regard to undated references, the latest edition of the publication to which it refers shall apply. NF T 30-053 Paints — Determining resistance to liquids. NF X 08-012 Colours – Colorimetric characteristics of coloured samples – Measuring devices and methods..
12、 NF X 08-014 Colours – Colorimetric deviations and tolerances – Formulae for colour differences between CI LUV and CIE LAB.. 3 General principle The evaluation procedures must include the following criteria: — material or coating; — graffiti application product; — graffiti removal product.
13、The behaviour of materials is evaluated on the basis of the graffiti and removal products defined by the client railway company. The results of the graffiti removal are evaluated after several “graffiti application – removal” cycles on the basis of the following criteria: — aggressivity (visual as
14、pect); — effectiveness (colorimetry); — safety labels on removal products (according to the laws in force). 4 Preparation of test specimens 4.1 Shapes and dimensions of test specimens The test specimens will be made either of the material itself in its as delivered condition, or a coating app
15、lied to a flat, rigid substrate in accordance with the corresponding technical data sheets. Their dimensions wil be (300 mm 1 mm x 210 mm 1mm). The thicknesses may vary from one test specimen to the other. 4.2 Test specimen preparation After removing any stripping agents, the test specimens wil
16、l cleaned using paper towels soaked in ethanol. 4.2.1 Test specimen for aggressivity test The test specimen may be divided into zones at least 100 mm x 210 mm in size. 4.2.2 Type test specimen for effectiveness test After drying the specimen, it will be divided into rectangles using adhesive tap
17、e, as shown in Appendix A. Each rectangle thus formed will contain a single graffito. An untreated zone will be kept on each test specimen to serve as a reference zone. 4.3 Test specimen storage The test specimens will be stored for at least 24 hours under the following conditions: — temperatur
18、e between 18C and 25C; — relative humidity < 75%. 5 Graffito application 5.1 Graffito dimensions The “graffito” must fill a rectangular area approximately 50 x 30 mm. 5.2 Equipment used In the case of a “graffito” using ink, the ink pad of the marker, or a flat (dry) paintbrush around 25 mm wi
19、de shall be used. In the case of a “graffito” using paint, the paint will be applied, after masking the area if necessary, using a spray gun or a flat (dry) paintbrush around 25 mm wide. 5.3 Application of the graffiti product Apply the graffiti product in parallel strokes in the same directio
20、n until the required dimension is achieved; repeat in the other direction to obtain an even “graffito” with no excess ink. This graffito will required a quantity of 0.75 ml 0.05 ml. It is applied to the test specimen horizontally under the following conditions: — temperature between 18C and 25C;
21、 — relative humidity < 75%. 6 Graffito elimination procedure The graffiti removal product will be applied using a flat 25 mm wide paintbrush. Apply the removal product in overlapping strokes in alternate directions, then make it penetrate well by brushing the surface of the "graffito" with a circ
22、ulation motion for 15 secs. Allow to take effect for 2 min 10 secs. Take a paper towel soaked in water and wrung out by hand before use, then slide it firmly in a single movement from one edge to the other, over the entire length of the graffito. If necessary, repeat this operation once again to
23、remove any surface residue. Take a dry paper towel and repeat the same movement to remove all traces of water. After waiting for 5 to 10 minutes since the last operation, repeat the graffito removal procedure once more. After the last removal operation, store the test specimens in a dark, dust-fr
24、ee place until the measurements can be taken for the effectiveness test (see article 8). 7 Aggressivity test 7.1 Test principle The purpose of the test is to check the aggressivity of the graffit removal products on the materials. 7.2 Test method The test is performed according to standard NF T
25、 30-053, method 2, with the following stipulations: — the absorbant material is a common filter paper 90 mm in diameter. It is soaked with 1 ml of removal product in its as used condition, and left in contact with the material for 24 hours under a watchglass; — the paper filter is then removed and
26、 the material rinsed using a paper towel soaked in water, then dried. 7.3 Expression of results The material is examined immediately after drying, and after being stored for 24 hours in a dark, dust-free place, the “material/removal product” pair will be graded: — GOOD, if after both examinati
27、ons no damage to the surface can be seen by the naked eye; — SATISFACTORY, if one or more imperfections that appeared immediately after drying have disappeared after 24 hours; — POOR, if the imperfection(s) remain after 24 hours. 8 Effectiveness test 8.1 Test principle The purpose of the test
28、 is to determine the colorimetric deviations between a material from which graffiti has been removed and the same material unaffected by graffiti (reference material). 8.2 Test method 8.2.1 Test specimens The test specimens are prepared and treated in accordance with articles 4, 5 and 6 of this d
29、ocument. 8.2.2 Operating procedure At least three graffiti application/removal operations are performed. The colorimetric deviations are measured after each operation in order to assess any increase in effectiveness. It is necessary to have three rectangles for a given removal product and graffit
30、i product (see type test specimen in Appendix A). The procedure is as follows: — apply a graffito to each rectangle; — after 48 hours, remove the three graffiti; — wait for 5 minutes, then repeat the removal operation; — do not perform any further operations on the first rectangle treated with
31、one graffito application and two removal operations; — store the test specimen for at least 24 hours under the conditions set down in paragraph 4.3; — apply a second graffito to the other two rectangles; — after 48 hours, remove the two graffiti; — wait for 5 minutes, the repeat the removal oper
32、ation; — do not perform any further operations on the second rectangle treated with two graffito applications and four removal operations; — store the test specimen for at least 24 hours under the conditions set down in paragraph 4.3; — apply the third graffito to the last rectangle; — after 48
33、hours, remove the last graffito; — after 5 minutes, perform the second removal operation on the last rectangle which corresponds to three graffito applications and six removals. 8.3 Measurement 8.3.1 Limit of measurement The measurement of the colorimetric deviations is not applicable to surfac
34、es containing decorative patterns with no line of symmetry, or when the dimension of the motifs in the pattern are smaller than the zone necessary for the measurement. In this case, only visual inspection can be used at present. 8.3.2 Equipment A spectrocolorimeter or colorimeter according to stan
35、dard NF X 08-012 can be used. 8.3.3 Measuring conditions The colorimetric measurements must be taken no sooner than 24 hours after the last removal operation. The previously calibrated device shows any colorimetric deviations (delta E) between the reference zone and the test zones. The colorimet
36、ric deviations are measured according to standard NF X 08/014, with the following stipulations. 8.3.3.1 Spectrocolorimeter — illuminant for observing the differences is D65; — diameter of observation window is 22 mm; — three measurements to be taken in each graffiti-affected zone and the average
37、 of these measurements to be recorded. 8.3.3.2 Colorimeter — illuminant for observing the differences is D65; — diameter of observation window is 8 mm; — nine measurements to be taken in each graffiti-affected zone and the average of these measurements to be recorded. 8.4 Expression of results
38、 The colorimetric deviations (delta E) are expressed according to the CIE 1976 colour space (L*, a*, b*). They can be presented in graph or chart form (see appendix B). The result is “GOOD” when all the average deviations are < 1. The result is “SATISFACTORY” when only one mean deviation is > 1
39、and > 2.5 and the other mean deviations are < 1. The result is “POOR” when at least one mean deviation is > 2.5. 9 Evaluation of aggressivity and effectiveness 9.1 Agressivity The behaviour of the “material/removal product” pair is said to be “NON AGGRESSIVE” when the result is good or satisfac
40、tory. 9.2 Effectiveness For a given material and removal product, this evaluation is made on the basis of the results obtained on samples of graffiti products, at the end of the “graffiti application – removal” cycles. The behaviour of the “material/removal product” pair is said to be “EFFECTIVE”
41、 when only one result is found to be “SATISFACTORY” and no results are found to be “POOR”. Otherwise, its behaviour will be deemed “INEFFECTIVE”. 10 “G” grading of the material On the basis of the removal products recognized non aggressive and effective, “G” grading includes the health and safety
42、aspects of the removal products, in accordance with current legislation. Otherwise, the material will be deemed “UNCLEANABLE”. On this basis, the grading system is as follows: — G 0: material is "CLEANABLE" with water or dry; — G 1: material is “CLEANABLE" using a removal product that is not
43、labelled with the danger symbol; — G 2: material is “CLEANABLE” using a removal product that is labelled “Xi” irritant and/or “F” inflammable. — G 3: material is “CLEANABLE” using a removal product that is labelled “Xn” harmful and/or “C” corrosive. — G 4 : material is “CLEANABLE" using a r
44、emoval product that is labelled “T” toxic; — NN: material is “UNCLEANABLE”. This grading of the selection of graffiti products is only valid under the conditions defined by the client railway company. Appendix A (normative) Type test specimen for effectiveness test Dimensions in millimeters
45、 Material Graffiti product Removal product: P1 Removal product: P2 1st graffiti + 2 removal operations 1st graffiti/1 + 2 removal operations plus 2nd graffiti/1 + 2 removal operations 1st graffiti/1 + 2 removal operations plus 2nd graffiti/1 + 2 removal operations 3rd graffiti/1 +
46、 2 removal operations Reference zone Adhesive tape Fig. A1 Appendix B (for information) Presentation of mean colorimetric deviations Material designation Graffiti product G Removal product P Presentation in graph form 1st graffiti 2nd graffiti 3rd graffiti 2 removal operations 4 removal operations 6 removal operations Presentation in chart form Graffiti product Graffito Number of removal operations Removal products Delta E (mean) Product 1st 2 0.80 G 2nd 4 1.80 3rd 6 2.80
- 溫馨提示:
1: 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
2: 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
3.本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
5. 裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 2025年防凍教育安全教育班會全文PPT
- 2025年寒假安全教育班會全文PPT
- 初中2025年冬季防溺水安全教育全文PPT
- 初中臘八節2024年專題PPT
- 主播直播培訓提升人氣的方法正確的直播方式如何留住游客
- XX地區機關工委2024年度年終黨建工作總結述職匯報
- 心肺復蘇培訓(心臟驟停的臨床表現與診斷)
- 我的大學生活介紹
- XX單位2024年終專題組織生活會理論學習理論學習強黨性凝心聚力建新功
- 2024年XX單位個人述職述廉報告
- 一文解讀2025中央經濟工作會議精神(使社會信心有效提振經濟明顯回升)
- 2025職業生涯規劃報告自我評估職業探索目標設定發展策略
- 2024年度XX縣縣委書記個人述職報告及2025年工作計劃
- 寒假計劃中學生寒假計劃安排表(規劃好寒假的每個階段)
- 中央經濟工作會議九大看點學思想強黨性重實踐建新功