喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有，CAD圖紙均為可自行編輯，有疑問咨詢QQ:1304139763
======================
喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有，CAD圖紙均為可自行編輯，有疑問咨詢QQ:1304139763
======================
E 型片畢業論文設計 1 E 型片復合模具設計 摘 要：本設計為一 E 型片的冷沖壓模具設計，根據設計零件的尺寸、材料、批 量生產等要求，首先分析零件的工藝性，確定沖裁工藝方案及模具結構方案，然后通過工 藝設計計算，確定排樣和裁板，計算沖壓力和壓力中心，初選壓力機，計算凸、凹模刃口 尺寸和公差，最后設計選用零、部件，對壓力機進行校核，繪制模具總裝草圖，以及對模 具主要零件的加工工藝規程進行編制。其中在結構設計中，主要對凸模、凹模、凸凹模、 定位零件、卸料與出件裝置、模架、沖壓設備、緊固件等進行了設計，對于部分零部件選 用的是標準件，就沒深入設計，并且在結構設計的同時，對部分零部件進行了加工工藝分 析，最終才完成這篇畢業設計。 關鍵詞：模具；沖裁件；凸模；凹模；凸凹模； E 型片畢業論文設計 2 Abstract: The design for E-type film of cold stamping die design, according to the size of the design components, materials, production requirements, the first part of the process of determining blanking die structure of the programme and the programme, and then through the design process, Determine layout and the Conference Board, and the calculation of the pressure-pressure center, the primary presses, calculated convex and concave-edge size and tolerance, the final design is selected, components, to check on the press, assembly and drawing the draft die, and Die major parts of the processing technology for the preparation of a point of order. In the design of the structure, mainly on punch, die, die Tuao, positioning parts, and the unloading of the device, model planes, stamping equipment, such as fasteners for the design, selection of some parts of the standard parts , There is no in-depth design, structural design and in the meantime, some parts of the processing technology for the analysis and eventually graduate to complete this design. Key words: Die; blanking pieces; punch; die; Tuao die; E 型片畢業論文設計 3 目錄 摘 要 .......................................................................................................................................................1 1 前言 ...................................................................................................................................................3 1.1 沖壓技術概論 .................................................................................................................................3 1.2 我國模具技術的發展趨勢 ...........................................................................................................5 1.3 本套模具設計要點 .....................................................................................................................10 2 制定 E 型片的工藝過程 ...................................................................................................................12 2.1 分析零件的沖裁工藝性 .............................................................................................................12 2.2 確定沖裁工藝方案 .....................................................................................................................12 3 排樣、裁板、利用率計算 ..................................................................................................................13 3.1 排樣 .........................................................................................................................................13 3.2 裁板及利用率計算 .....................................................................................................................14 4 計算工序壓力，選用壓力機及確定壓力中心 ..................................................................................17 4.1 計算工序沖壓力，選用壓力機 ...................................................................................................17 4.2 確定壓力中心 ...............................................................................................................................17 5 計算凸凹模刃口尺寸，及其計算原則 ...........................................................................................19 5.1 尺寸計算原則 .............................................................................................................................19 5.2 凸凹模刃口部分尺寸 .................................................................................................................19 6 設計選用零件、部件，繪制模具總裝草圖 ...................................................................................21 6.1 凹模設計 .....................................................................................................................................21 6.2 墊板的采用與厚度 .......................................................................................................................23 6.3 確定卸料橡皮的自由高度 ...........................................................................................................23 6.4 凸模長度 的確定 ....................................................................................................................231L 6.5 凸凹模設計 ...................................................................................................................................24 6.6 定位零件 .....................................................................................................................................25 6.7 卸料與出件裝置 .........................................................................................................................25 6.8 模架及其它零件的選用 ...............................................................................................................26 6.9 沖壓設備的選擇 ...........................................................................................................................27 6.10 緊固件的選用 ...........................................................................................................................27 7 壓力機的校核 ...................................................................................................................................28 7.1 公稱壓力 .....................................................................................................................................28 7.2 滑塊行程 .....................................................................................................................................28 7.3 行程次數 .....................................................................................................................................28 7.4 工作臺面的尺寸 .........................................................................................................................28 7.5 滑塊模柄孔尺寸 .........................................................................................................................28 7.6 閉合高度 .....................................................................................................................................28 E 型片畢業論文設計 4 8 模具主要零件加工工藝規程的編制 .................................................................................................30 8.1 沖壓模具制造技術要求 ...............................................................................................................30 8.2 總裝工藝 .......................................................................................................................................30 8.3 加工要求 .......................................................................................................................................31 8.4 主要零、部件加工工藝 .............................................................................................................32 致 謝 .................................................................................................................................................34