滾筒混合機混合單元的設計-自落式混凝土攪拌混合機的設計研究含開題及8張CAD圖

滾筒混合機混合單元的設計-自落式混凝土攪拌混合機的設計研究含開題及8張CAD圖,滾筒,混合,單元,設計,混凝土,攪拌,研究,鉆研,開題,cad 自落式混凝土攪拌混合機的設計研究 摘要：最近幾年，建筑行業蓬勃發展。而在建筑機械里，混凝土攪拌機械是其中的基本設備之一。攪拌的混凝土關系到建筑的質量，而過去的機型如鼓筒型混凝土攪拌機存在許多問題如攪拌質量差、時間長、能耗高。自落式混凝土攪拌機尤其是其中之一的錐形反轉出料攪拌機能更好的解決上述問題。 本文通過綜合優化設計和類比的方法，結合以往的參數、數據和給出的原始資料、技術要求，對自落式混凝土攪拌機進行了設計。利用攪拌筒直徑d=1560mm和其他條件，計算出攪拌筒的轉速n=18r/min。根據原始數據——分批混合：1000kg/批、攪拌筒厚度h=4mm、裝機容量：7.5千瓦、生產率：8-10噸/時等條件，計算出攪拌筒和混合料、支撐滾輪間相互作用的總力矩M，傳動裝置的總效率=0.89，從而得出減速電機額定功率=7.5kw，減速比i=23，轉速n=1500r/min。考慮攪拌機傳動系統的要求，對托滾軸和減速電機之間采用鏈傳動的連接方式，鏈傳動比i=1.19，小鏈輪齒數Z=17，從動鏈輪齒數Z=20，鏈長L=2.5146mm,中心距a=1020.5mm。再確定要安裝鏈輪和拖輪的托滾軸，材料為45#，調質處理，軸的最小處直徑d=69mm。根據材料和載荷，設計出托滾軸的各段的長度和直徑，最后進行校核驗證。 關鍵詞：減速電機 混合單元摩擦傳動 托滾軸設計 鏈傳動 指導老師簽名： gravity type concrete mixing mixer design Abstract: In recent years, the construction industry develops rapidly. In the construction machinery, the concrete mixing machine is one of the basic equipment. The mixing concrete related to the quality of construction, but the past models such as the type of drums concrete mixer has many problem such as poor mixing quality, long duration and high energy consumption. The gravity type concrete mixing mixer especially one of these： cone reversal discharging mixer can solve the above problem for the better. Considering the previous parameters,data and original data,technical requirements which has given,this papers design the gravity type concrete mixing mixer taking the methods of integrated optimal design and analog. Using the mixing tube diameter d = 1560mm and other conditions to calculate the speed of mixing tube n = 18r/min. According to the original data - batch mixed: 1000kg / batches, the mixing tube thickness h = 4mm, capacity: 7.5 kW, 8-productivity of 10 tons / h and other conditions, to calculate the total moment M between mixing tube and mixture as well as interaction support rollers, the overall efficiency of gear=0.89, so as to receive the gear motor rated power=7.5kw, reduction ratio i = 23, rotational speed n = 1500r/min. Considering the request of the mixer drive system， the placement between the care roller and the gear motor is connected by chain drive ，chain drive ratio i = 1.19, the small sprocket number of teeth Z = 17, and the driven sprocket number of teeth Z = 20, chain length L = 2.5146mm, center distance a = 1020.5mm. Next,confirming the care roller which demand installing the chain wheel and tug ，to determine its material is 45#、quenching and tempering, the minimum diameter of shaft is d = 69mm. According to the material and the loading, we design the roller care of all of the length and diameter , and check verification finally. Key words: Geared Motor Mixed friction drive unit Care roller design Chain drive Signature of Supervisor: