微型車離合器設計【膜片彈簧離合器】

微型車離合器設計【膜片彈簧離合器】,膜片彈簧離合器,微型車離合器設計【膜片彈簧離合器】,微型車,離合器,設計,膜片,彈簧 黑龍江工程學院本科生畢業設計 摘 要 汽車離合器位于發動機和變速箱之間的飛輪殼內，用螺釘將離合器總成固定在飛輪的后平面上，離合器的輸出軸就是變速箱的輸入軸。 離合器是汽車傳動系中的重要部分，在機械傳動系中是作為一個獨立的總成而存在的，它是汽車傳動系中直接與發動機相連接的總成，對汽車的性能起著重要的作用。此次設計離合器是主要目的是利用傳統的設計方法，學習傳統方法中的基本步驟，了解設計過程，把學過的知識綜合的運用到設計過程中，從而更堅實的掌握學過的知識。 離合器設計的內容主要包括壓盤總成、從動盤總成、膜片彈簧三個部分。首先，對離合器各零件的參數、尺寸、材料、及結構進行設計，然后用Auto CAD工程圖。 本文主要是對轎車的膜片式彈簧離合器進行設計。根據車輛使用條件和車輛參數，按照離合器系統的設計步驟和要求，主要進行了以下工作：選擇相關設計參數主要為：摩擦片外徑的確定，離合器后備系數的確定，單位壓力的確定。并進行了總成設計主要為：分離裝置的設計（包括分離軸承、分離套筒等），以及從動盤設計包括從動片設計和從動盤轂設計，主動部分的設計，包括壓盤、離合器蓋設計、彈性傳動片設計，其中離合器蓋的設計只是簡單的設計，操縱機構的設計是大體上計算出踏板的行程、踏板力，是否符合人體工程學要求。扭轉減震器中的螺旋彈簧的設計。還重點研究了膜片彈簧在分離過程中的受力，對受力過程進行數學分析，并對其進行校核，以提高膜片彈簧離合器的使用壽命，使膜片彈簧離合器在工作過程中處于最佳狀態。 關鍵詞：離合器；壓盤；從動盤；膜片彈簧；摩擦片 ABSTRACT Automobile Clutch in the engine and gearbox between the flywheel shell, with screw will be fixed in the clutch assembly after the plane of the flywheel, clutch gearbox output shaft is the input shaft。 Automobile clutch is an important part of the power train of the car ,it plays an important role. The main purpose of this design is using traditional methods to learn the basic steps, comprehending the design process, using the learned knowledge to the design process, thus a more solid grasp of the knowledge learned. There are three main parts of the clutch design: driven disc design, diaphragm-spring design and the driving disc design. Firstly, this paper calculates the parameters, and chooses sizes and materials for the clutch’s parts. Then draw the three-dimension-blueprint of the assembly and components. Finally transforms the three-dimension-blueprint into Auto CAD engineering plat. This paper is a car diaphragm spring clutch design. In accordance with the conditions of vehicles and vehicle parameters, in accordance with the clutch system design steps and requirements for the following main tasks: choosing the main design parameters are: the determination of friction plate diameter, back-up clutch coefficient determination unit to determine the pressure. And designed primarily for the assembly: the design of separation devices (including the separation of bearings, sleeve separation, etc.), as well as the follower plate follower piece design includes the design and the design of the driven wheel disc, part of the design of the initiative, including the pressure plate, Clutch cover design, flexible drive chip design, which covered the design of the clutch is a simple design, is designed to manipulate the whole body out of the trip pedal, pedal power, with the ergonomic requirements. To reverse the shock absorber of the coil spring design.This paper also studies force exerted on diaphragm in the process of separation, and analyzing the process mathematically, then examines and calculates relative parameter. In conclusion, the design will prolong the lifetime of diaphragm-spring clutch, and makes the clutch in best state when it’s working. Key words: Clutch; Diaphragm Spring; Driven Plate; Pressure Plate; Friction Disc. III 黑龍江工程學院本科生畢業設計 得