喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:414951605 或 1304139763】
差速器外殼加工工藝工裝設計
? 學生姓名：曾威 班級：0781052
指導老師：王細洋
摘要：差速器是驅動轎的主件。差速器的作用就是在向兩邊半軸傳遞動力的同時，允許兩邊半軸以不同的轉速旋轉，滿足兩邊車輪盡可能以純滾動的形式作不等距行駛，減少輪胎與地面的摩擦。普通差速器由行星齒輪、差速器殼（行星輪架）、半軸齒輪等零件組成。發動機的動力經傳動軸進入差速器，直接驅動差速器殼帶動行星輪軸，再由行星輪帶動左、右兩條半軸，分別驅動左、右車輪。
本文主要是介紹了差速器外殼的加工工藝及加工中所需要的專用鏜床夾具的設計。首先對零件進行了工藝性分析了解各加工面所需要打到的加工精度，確定各個加工面的加工余量。制定合理的能夠滿足加工需要的工藝方案。為了保證零件的加工精度需要進行基準面的選擇和對零件的定位，并遵循一定基本原則，并進行定位誤差的分析。加工中還涉及到各種加床夾具的設計。本文主要介紹的是鏜床專用工藝方案的設計，主要有夾具的定位，零件與零件的連接、夾具體與機床的連接和誤差分析。
關鍵詞：加工工藝 工藝方案 夾具
指導老師簽名：
Differential case processing
Student:Zeng Wei Class:0781052
Supervisor:Wang Xiyang
Abstract:The main differential is the driving car parts. Differential role is to transmit power to the axle on both sides at the same time, allowing both sides of the axle rotating at different speeds to meet the both sides of the wheel as far as possible in the form of pure rolling road of no offset, reducing the friction between tire and ground. By the ordinary differential gear, differential case (planetary gear frame), side gears and other parts. The power of the engine drive shaft into the differential, direct-drive planetary drive axle differential case, then the planetary wheel drive left, right, two axle, respectively, drive left and right wheels.
?? This article is to introduce a differential case processing technology and processing needs of special boring machine in the fixture design. First of all parts of the process of analysis needed to understand the processing of surface machining accuracy to hit, to determine the allowance of each machined surface. To develop a reasonable process to meet the processing needs of the program. To ensure the machining accuracy is required datum selection and positioning of parts, and follow certain basic principles, and the positioning error analysis. Processing also involves a variety of extra fixture design. This paper describes the design of special fixture boring, there are fixture positioning, parts and components of the connection, the connection with the machine specific folder and error analysis.
Keywords:
Signature of supervisor：
目錄
1.零件的分析 2
1.1 零件的作用 2
1.2 零件的工藝分析 2
2. 工藝規程設計 3
2.1 毛坯的制造形式 3
2.2 基準面的選擇 3
2.2.1 粗基準的選擇 3
2.2.2 精基準的選擇 4
2.3 制訂工藝路線 4
2.3.1. 工藝線路方案一 4
2.3.2 工藝路線方案二 5
2.3.3. 工藝方案的比較與分析 5
2.4 機械加工余量、工序尺寸及毛坯尺寸的確定 6
2.4.1 外圓表面 6
2.4.2 內圓表面 8
2.4.3 端面 10
2.4.4 凸臺孔系 10
3. 夾具設計 11
3.1 問題的提出 25
3.2.1定位基準的選擇 25
結 論 27
參考文獻 28
附錄： 30