加工中心主軸傳動系統設計

加工中心主軸傳動系統設計,加工,中心,主軸,傳動系統,設計 摘 要 加工中心由于備有刀庫并能自動更換刀具，使得工件在一次裝夾中可以完成多工序的加工。加工中心一般不需要人為干預，當機床開始執行程序后，它將一直運行到程序結束。加工中心還賦予了專業化車間一些諸多優點，如：降低機床的故障率，提高生產效率，提高加工精度，削減廢料量，縮短檢驗時間，降低刀具成本，改善庫存量等。由于加工中心的眾多優勢，所以它深受全球制造企業的青睞。 加工中心主要由主軸組件、回轉工作臺、移動工作臺、刀庫及自動換刀裝置以及其它機械功能部件組成。其中的主軸組件是機床重要的組成部分，其運動性能直接影響機床加工精度與表面粗糙度。本文在查閱大量國內外文獻的基礎上，通過研究分析不同加工中心主軸組件的性能，綜合地比較了其特點，并擬定了一個較為合理的主軸組件結構方案。同時，還就主軸、軸承以及絲杠等重要零件的機械性能進行了探討，并對這些零件的剛度和強度進行了校核。此外，本設計中所采用的陶瓷軸承能有效地增加主軸的剛度，從而提高了加工中心的可靠性和穩定性。 關鍵詞 主軸組件；加工中心；數控機床 I Abstract Machining center evolved from the need to be able to perform a variety of operations and machining sequences on a workpiece on a single machine in one setup. Machining center requires little operator intervention, and once the machine has been set up, it will machine without stopping until the end of the program is reached. Some of the other advantages that machining centers give a manufacturing shop are greater machine uptime, increased productivity, maximum part accuracy, reduced scrap, less inspection time, lower tooling costs, less inventory and so on. Because of their many advantages, machining centers become widely accepted by manufacturing enterprises in the world. Machining centers are equipped with spindle units, rotary workbench, moving workbench, tool magazines and automatic tool changers, and other mechanical function components. Spindle unit is the important motion part of the metal cutting machine tool. Its movement behavior affects the machining accuracy and surface roughness of part to be machined. Through referring to a variety of technical literatures, the characteristics of some kinds of spindle units are compared with each other based on analysis and research work on different machining centers. A reasonable scheme can be studied out. Meanwhile, the mechanical behaviors of principle parts such as the spindle, bearings and lead screw are discussed. Their rigidity and strength are calculated and examined here. Morever, a kind of advanced ceramic bearings is introduced into the spindle unit, which can effectively enhance the rigidity of spindle units. They will improve the reliability and stability of machining centers. Key words spindle unit;machining center; NC machine tool -II- 目 錄 摘 要 I Abstract II 第1章 緒 論 1 1.1 加工中心的發展?fàn)顩r 1 1.1.1 加工中心的國內外發展 1 1.1.2 主軸部件的研究進展 2 1.3 課題擬解決的關鍵問題 3 1.4 解決上述問題的策略 4 第2章 方案擬定 5 2.1 加工中心主軸組件的組成 5 2.2 機械系統方案的確定 5 2.2.1 主軸傳動機構 5 2.2.2 主軸進給機構 6 2.2.3 主軸準停機構 7 2.3 加工中心主軸組件總體設計方案的確定 9 第3章 主軸組件的主運動部件 11 3.1 主軸電動機的選用 11 3.1.1 主電機功率估算 11 3.1.2 主電機選型 12 3.2 主軸 12 3.2.1 主軸的結構設計 12 3.2.1.1 主軸軸徑的確定 13 3.2.2 主軸受力分析 13 3.2.3 主軸的強度校核 16 3.2.4 主軸的剛度校核 17 3.2.5 軸承的配合 18 3.2.6 主軸軸承設計計算 18 3.2.6.1 軸承受力分析 18 3.2.6.2 軸承7017AC壽命計算 19 3.2.6.3 軸承7015AC壽命計算 19 3.3同步帶的設計計算 20 第4章 主軸組件的進給運動部件 24 4.1 進給電動機的選用 24 4.1.1 進給電動機功率的估算 24 4.1.2 進給電動機的選用 24 4.2 聯軸器的設計計算 25 4.3 垂直方向伺服進給系統的設計計算 25 4.3.1 切力削估算 25 4.3.2 滾珠絲杠副的設計計算 26 4.3.2.1 滾珠絲杠的導程的確定 26 4.3.2.2 確定絲杠的等效轉速 26 4.3.2.3 確定絲杠的等效負載 26 4.3.2.4 確定絲杠所受的最大動載荷 27 結 論 28 致 謝 30 參考文獻 31 附錄1 33 附錄2 37 -IV- - 5 -