履帶翻譯

1、1 附錄 外文翻譯資料 in 005of to 3D in be as of By in of to of of is to of 1 in of is in of is 3D as an in of is AD 2 of - on of to of AD on of to to in a of to a o it be in of of in of in to to of a is to AM 2 be to in of to of of to to to 2.2 to be to in of a of to be in to of of 3 be to as a 2.3 In to in a to of of as of 2.4 of of of in of of of of to of in of be to on by or by to by in As 4 AD of of It is to of of In 3D AD to of in of a of be on of of of In of in a of of it a in to as。

2、1 附錄 外文翻譯資料 in 005of to 3D in be as of By in of to of of is to of 1 in of is in of is 3D as an in of is AD 2 of - on of to of AD on of to to in a of to a o it be in of of in of in to to of a is to AM 2 be to in of to of of to to to 2.2 to be to in of a of to be in to of of 3 be to as a 2.3 In to in a to of of as of 2.4 of of of in of of of of to of in of be to on by or by to by in As 4 AD of of It is to of of In 3D AD to of in of a of be on of of of In of in a of of it a in to as。

3、哈爾濱理工大學學士學位論文 錄 A 1992： 88of to 3D in be as of By in of to of of is to of in of is in of is 3D as an in of 哈爾濱理工大學學士學位論文 TC is AD of - on of to of AD on of to to in a of to a o it be in of of in of in to to of a is to AM 2 be to in of to of of to to to 2.2 to be to in of a of to be in to of of be to as a 2.3 In to in a to of of as of 2.4 of of of in of of of of to of in of be to on by or by to by in As of of It is to of of 3D AD to of AD in of a of be on of of of In o。

4、外文資料翻譯 翻譯資料名稱 (外文 ) of 翻譯資料名稱 (中文 )基于傾角測量的鏈式履帶移動機器人 接 觸點 檢測 院 （ 系）： 機械工程系 專 業： 機械設計制造及 其自動化 姓 名： 李保坤 學 號： 04111220 指導教師： 林曉輝 完成日期： 2015 年 3 月 6 日 of 008 2008, Xi于傾角測量的鏈式履帶移動機器人的接觸點檢測 要 履帶式移動機器人可以根據周圍環境改變自身形式，在通過崎嶇地形時具有很高的機動性和穩定性。然而，對于操作手而言，熟練的遠程操控機器人是較困難的。解決問題的途徑之一就是組建一個自主控制系統，履帶和路面之間。

5、履帶式底盤設計,報告人：姚小海,機械工程學院 School of Mechanical Engineering,湘潭大學 Xiang Tan University,博學篤行 盛德日新,制作人：姚小海,機械工程學院 School of Mechanical Engineering,主要內容： 一、履帶式底盤結構 二、履帶式底盤設計參數的選定 三、面臨的問題和需要做的工作 四、文獻資料的查找,機械工。

6、履帶吊,1,GB/T14560履帶起重,2,產品銘牌 生產廠、名稱、型號齊全并固定于明顯處,3,起重性能標牌 應有額定起重量、性能參數及起升高度曲線，且固定于操作者便于看到的位置,4,主要結構件外觀 不得有可見裂紋、變形和嚴重腐蝕,焊接外觀質量 無漏焊、氣孔、凹陷、夾渣、可見裂紋等缺陷,5,主要結構件連接螺栓應齊全，緊固,配重連接螺栓,履帶板連接螺栓,6,主要結構件連接銷軸及軸端固定,開口銷,7,謝謝觀賞,主要結構件連接銷軸及軸端固定,開口銷,8,止退墊片,9,吊鉤,吊鉤保險,10,11,12,鋼絲繩,卷筒防脫保險,13,繩筒兩側邊緣的高度 應超過最外層鋼。

7、150噸液壓履帶起重機安裝方案 履帶起重機150噸液壓履帶起重機安裝方案 一、編制依據 1、QUY150液壓履帶起重機使用說明書 2、履帶起重機安全規程 3、起重機械監督檢驗規程 二、設備概況 1、QUY150液壓履帶起重機最大額定起重量150t，起重能力750tm，主臂長81m，副臂長31m，最大工作幅度60m，吊鉤地上最大高度93m。本次組立工況為 27 m主臂， m副。

8、橡膠履帶板】淺談履帶板鏈節的鑄造工藝設計及模擬優化設計 【摘 要】履帶板鏈節作為工程機械中重要的采掘機械完成采掘工作的重要設備和重要組成部分，特別適合應用在露天礦、大型土方工程中的采、運、排連續開采工藝。隨著我國經濟的快速發展，我國的工程機械發展與國外相比，雖然能夠滿足國內市場和國際市場的巨大需求，但是仍然還有較大的上升空間和上升幅度，仍然存在很多不足之處。大型化是市場的發展趨勢，因此對于大。