購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。帶三維備注的都有三維源文件，由于部分三維子文件較多，店主做了壓縮打包，都可以保證打開的，三維預覽圖都是店主用電腦打開后截圖的，具體請見文件預覽，有不明白之處，可咨詢QQ:1304139763===========題目最后備注XX系列，只是店主整理分類，與內容無關，請忽視
2110型柴油機氣缸蓋加工工藝規程設計及夾具設計。
摘 要
這次畢業設計的題目是：2110型柴油機氣缸蓋加工工藝規程設計及夾具設計。
氣缸蓋是柴油機的重要零部件之一，屬于典型的箱體類零件。他的結構比較復雜，其加工質量的好壞將直接影響到柴油機的整體性能。
通過對零件圖的分析可知：氣缸蓋的底面、氣道孔及底面座孔的技術要求加高，是重要的平面，因此需要精細加工。
由零件的年生產綱領可以確定該零件為大批量生產。毛坯采用HT20—40的鑄鐵由機器進行砂模鑄造。
粗加工時，選取氣缸蓋的上下底面互為基準；精加工時，選取加工過的氣缸蓋底面為基準。以底面及底面上的兩個銷進行定位，即“一面兩銷”式定位。
在查閱了一些相關的資料，并仔細地分析了大連柴油機廠的氣缸蓋加工工藝路線和其它一些同類產品的生產線狀況后，才具體地制定了這次設計的工藝方案。實際的機械加工工序安排，遵循著：先主要、后次要，先粗后精，先面后孔等原則。
根據生產批量和生產實際情況，工序的安排采用了工序集中和工序分散相結合的辦法，并且設計了一條自動化生產線DX33.當按工序集中原則組織過程時，還普遍的采用了自動化程度較高的高效機床和工藝裝備。這樣，大大地提高了生產率。
工藝方案中的工序310，采用了專用機床，在自動線上進行加工。因此，需要設計“一面兩銷”式專用夾具。其中一銷為短圓柱銷，另一銷為削邊銷，分別限制2個和1個自由度。
Abstract
The topic of this graduation project is: 2110 type diesel engine air cylinders build processing technology design by rules and the clamping apparatus is designed.
It is one of the important spare part of a diesel engine that the air cylinder is covered, belong to the typical case body type part. It relatively complicated structure, its the qualities of quality influence globality can diesel engine directly.
Can know through the analysis to the picture of part: Bottom surface who air cylinder build, Kong bottom surface seat the specification requirements of hole increase angry ones, It is the important plane, so need retrofit
Can be confirmed this part as and produced in enormous quantities by producing the guiding principle annually of the part. Blank adopt HT go on sand mould's casting by machine by casting iron as much as 20-40.
At the rough machining, choose about bottom surface who air cylinder stamp interact as the datum; At the finish machining, choose air cylinder that process leave datum on bottom surface. At bottom surface and eaches on the bottom surface sell and go on and make a reservation, namely" each sell at two" the type make a reservation.
It consults relevant materialses analyse diesel engine of Dalian the air cylinders of factory build route and similar the production lines of productses after the state processing technology carefully, Have made this technology scheme designed concretly . The real machining process is arranged, is following : It is neither first main, afterwards less important nor first after being thick precise, the hole waits for the principle after one first.
At production lot and reality of producing, the arrangements of process adopt in collecting and process disperse way that combine together process, Design one a piece of automatic production line DX 33s. When concentrate the principle on organizing the course according to the process, also relatively and technology equip high high-efficient lathes general adoption automatic degrees. So, have boosted productivity greatly .
Technology 310 processes of the scheme, it adopts special-purpose lathe process at the transfer machine. However, need and design " each sell at two" type special-purpose clamping apparatus. Sell and sell for short cylinders among them and sell and for paring and sell, limit each and 1 a piece of degree of freedoms respectively at another.