壓縮包已打包上傳。下載文件后為完整一套設計?！厩逦?，無水印，可編輯】dwg后綴為cad圖紙，doc后綴為word格式，所見即所得。有疑問可以咨詢QQ 197216396 或 11970985
摘 要
數控車床又稱數字控制（Numbercal control，簡稱NC）機床。它是基于數字控制的，采用了數控技術，是一個裝有程序控制系統的機床。它是由主機，CNC，驅動裝置，數控機床的輔助裝置，編程機及其他一些附屬設備所組成。
本次設計課題是CK6140數控臥室車床，CK是數控車床，61是臥式車床，40是床身上最大工件回轉直徑為400mm。
此次設計包括機床的總體布局設計，縱向進給設計，其中還包括齒輪模數計算及校核，主軸剛度的校核等。控制系統部分包括步進電機的選用及硬件電路設計和軟件系統設計，說明了芯片的擴展，鍵盤顯示接口的設計等等。
關鍵詞 數控機床；開放式數控系統；電動機
Abstract
The numerical control lathe called the numerical control (Numbercal control, is called NC) the engine bed. It is based on the numerical control, has used the numerical control technology, is loaded with the procedure control system the engine bed. It is by the main engine, CNC, the drive, the numerical control engine bed auxiliary unit, the programming machine and other some appurtenances is composed.
This design topic is the CK6140 numerical control bedroom lathe, CK is the numerical control lathe, 61 is the horizontal lathe, 40 is on the lathe bed the biggest work piece rotation diameter is 400mm.
This design including the engine bed overall layout design, longitudinal enters for the design, also includes the gear modulus computation and the examination, the main axle rigidity examination and so on. The control system partially including step-by-steps the electrical machinery to select and the hardware circuit design and the software system design, explained the chip expansion, keyboard demonstration connection design and so on.
Key word numerical control tool;Open-architecture;motor
目 錄
1 總體方案設計
1.1 CK6140的現狀和發展
1.2 CK6140數控臥式車床的總體方案論證與擬定
2 機械部分設計計算說明
2.1 主運動部分計算
2.1.1 參數的確定
2.1.2 傳動設計
2.1.3 轉速圖的擬定
2.1.4 帶輪直徑和齒輪齒數的確定
2.1.5 傳動件的估算和驗算
2.1.6 展開圖設計
2.1.7 截面圖設計
2.2縱向進給運動設計
2.2.1 滾珠絲桿副的選擇
2.2.2 驅動電機的選用
3 控制系統設計
3.1繪制控制系統結構框圖
3.2.選擇中央處理單元（CPU）的類型
3.3存儲器擴展電路設計
3.4?I/O接口電路及輔助電路設
參考文獻
謝詞
附錄