購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。帶三維備注的都有三維源文件，由于部分三維子文件較多，店主做了壓縮打包，都可以保證打開的，三維預覽圖都是店主用電腦打開后截圖的，具體請見文件預覽，有不明白之處，可咨詢QQ:1304139763===========題目最后備注XX系列，只是店主整理分類，與內容無關，請忽視
河南機電高等專科學校材料工程系畢業(yè)設計/論文
摘 要
本設計的題目是泡沫滅火器噴嘴，通過塑件的工藝分析、注塑模結構設計及有關計算、模具閉合高的的確定、注塑機有關參數的校核等，該模具基本符合要求。
該塑件要求表面沒有毛刺、凹陷等缺陷，沒有其它特別要求，故注塑較易實現(xiàn)。根據塑件的成型要求及模腔的排列方式，選用潛伏式澆口比較合適，該模具型芯采用組合式結構，有利于填充、排氣。
型芯主要是成形制件的內表面，本模具把型芯固定在定模一側，這樣可以簡單模具的結構。考慮加工的難易程度和材料的價值利用、塑件的形狀和尺寸，并考慮到塑件的生產率，本模具采用一模二件的結構形式；凹模主要成型塑件外表面，結構較簡單，將型腔設計成組合式結構，既保證塑件外觀與質量，模具加工也比較方便。從塑件結構上看，將型腔與斜滑塊設計在一起，組成一個抽芯機構。
關鍵詞：一模二腔、組合式型腔、斜滑塊抽芯、 潛伏式澆口。
Take off to want
The topic of this design is a knob to note the mold of part designs, the piece of part craft analysis, and the mold construction design and relevant calculation, the molding tool shuts to match high really settle, note the machine of the concerning parameter etc., that molding tool is basic to meet the request.
The part's piece requests the surface has no the hair stabs, hollow etc. blemish, inner part cannot conduct electricity the miscellaneous quality, have no other special request, so note the part than realizes easily.According to an alignment for modeling request and moldings method, choose to sprinkle with the side comparison accommodation, design, consider the choice from the wall the thick 3 mms enters to anticipate, anticipate to flow to thin place from the thick place, and the molding tool's type adopts the sectional construction, benefitting to fill , row spirit.
The convex mold is a difficult easy degree to take shape a the piece of system inside surfaces, consider to process primarily with the material of worth a make use of, a rate of production for of shape with size, combining in consideration of the piece of the part , this molding tool adoption is sectional to model a mold six pieces constructions form;The cave mold models the part an outward appearance primarily, construction than simple, design the cave mold sectional construction, since guarantee the part an external appearance and quantity, the molding tool processes too more convenient.
Because design of ability limited, design inside exsit a lot of not enough places, still hope the teacher gives to advise with understand.
Key word: A The mold two , inclined slippery pieces ,take out the and incubare ,the type to sprinkle.