3808 長接頭注塑模設計

3808 長接頭注塑模設計,接頭,注塑,設計 畢業設計說明書目錄緒 論 ...............................................................1第 1章 注塑模的設計要求 .............................................31.1 合理的選擇模具結構 ............................................31.2 正確地確定模具成型零件的尺寸 ..................................31.3 設計的模具應制造方便 ..........................................31.4 模具零件應耐磨耐用 ............................................3第 2章 模塑工藝規程的編制 ...........................................42.1 塑件的工藝性分析 ..............................................42.1.1 塑件的原材料分析 ........................................42.1.2 塑件的結構和尺寸精度及表面質量分析 ......................42.2 計算塑件的體積和質量 ..........................................52.3 塑件注塑工藝參數的確定 ........................................5第 3章 注塑模的結構設計 .............................................73.1 分型面的選擇 ..................................................73.2 確定型腔的排列方式 ............................................83.3 澆注系統設計 ..................................................83.3.1 主流道設計 ..............................................83.3.2 分流道設計 ..............................................93.3.3 澆口設計 ................................................93.3.4 定位環與主流道襯套設計 ..................................93.4 抽芯機構設計 ..................................................93.4.1 確定抽拔距 ..............................................93.4.2 確定斜導板傾角 ..........................................93.4.3 確定斜導板的尺寸 ........................................93.4.4 斜導槽、導滑套與導滑槽設計 .............................10畢業設計說明書目錄3.5 成型零件結構設計 .............................................103.5.1 凹模結構設計 ...........................................103.5.2 凸模結構設計 ...........................................103.5.3 螺紋型環設計 ...........................................11第 4章 模具設計的有關計算 ..........................................124.1 型腔和型芯工作尺寸計算 .......................................124.2 型腔側壁厚度和底板厚度計算 ...................................134.2.1 上下凹模型腔側壁厚度計 .................................134.2.2 上下凹模型腔底板厚度計算 ...............................13第 5章 模具冷卻與加熱系統的計算 ....................................15第 6章 模具閉合高度的確定 ..........................................16第 7章 注塑機有關參數的校核 ........................................17第 8章 模具裝配 ....................................................188.1 模具安裝 .....................................................188.2模具工作原理 .................................................188.3 注塑問題及其解決方法 .........................................188.3.1 粘著模腔 ...............................................198.3.2 粘著模芯 ...............................................198.3.3 粘著主流道 .............................................198.3.4 成型缺陷 ...............................................208.3.5 調整措施 ...............................................21第 9章 模具典型零件機械加工工序卡 ..................................22畢業設計說明書目錄小 結 ..............................................................23致 謝 ..............................................................24參考文獻 ............................................................25