【溫馨提示】 dwg后綴的文件為CAD圖，可編輯，無水印，高清圖，，壓縮包內文檔可直接點開預覽，需要原稿請自助充值下載，請見壓縮包內的文件及預覽，所見才能所得，請細心查看有疑問可以咨詢QQ：414951605或1304139763
文檔包括:
說明書一份,53頁,21200字左右.
翻譯一份.
圖紙共3張:
A0-變速器裝配圖.dwg
A0-變速器后殼.dwg
A0-變速器上蓋.dwg
畢業設計（論文）
摘要
變速器是汽車傳動系中的主要部件之一。變速器由變速傳動機構和變速操縱機構兩部分組成。變速傳動機構的主要作用是改變轉距和轉速的數值和方向；操縱機構的主要作用是控制傳動機構，實現變速器傳動比的改變，即實現換擋，以達到變速變距。本題目主要進行轎車三軸六擋機械式變速器的設計，包括變速器的整體結構和齒輪傳動部分的設計，并進行相關的計算與校核。經過設計與校核，該變速器主要結構符合設計標準、零件強度也達到了使用要求。
關鍵詞：汽車機械變速器；三軸六擋；傳動比；齒輪
Abstract
Transmission in the automotive transmission lines, one of the most important components. Transmission speed by a variable speed transmission and control mechanism of two parts. The main role of the variable-speed transmission is to change the value of torque and rotational speed and direction; manipulation of the organization's main role is to control the transmission mechanism, transmission gear ratio to achieve the exchange, that is, to achieve shift in order to achieve variable-speed pitch. This subject, mainly for automotive six-axis mechanical transmission gear structural design, including the gear drive parts, control of part of the, etc., and the associated calculation and verification, through the design and verification,The main structure of the transmission line design standards, parts intensity reached the use requirements.
Keywords: Automotive Mechanical Transmission；Axis 6 block ；gear ratio；gear wheel
目錄
- III -
摘要 I
Abstract II
第1章 緒論 1
1.1 選題的背景及意義 1
1.2 變速器的功用和要求 2
1.3 國內外研究狀況 3
1.4 部分已知的主要參數 5
1.5 本章小結 6
第2章 機械式變速器的概述及其方案的確定 7
2.1 變速器結構方案的確定 7
2.1.1 變速器傳動機構的結構分析與型式選擇 7
2.1.2 倒擋傳動方案 12
2.2 變速器主要零件結構方案的分析 13
2.2.1 齒輪型式 13
2.2.2 換擋機構型式 13
2.3 本章小結 16
第3章 變速器主要參數的選擇與主要零件的設計 17
3.1 變速器主要參數的選擇 17
3.1.1 擋數和傳動比 17
3.1.2 中心距 18
3.1.3 軸向尺寸 19
3.1.4 齒輪參數 19
3.2各擋傳動比及其齒輪齒數的確定 21
3.2.1 確定各擋齒輪的齒數 21
3.2.2 齒輪變位系數的選 23
3.3 變速器齒輪的強度計算與材料的選擇 24
3.3.1 齒輪的損壞原因及形式 24
3.3.2 齒輪的強度計算與校核 24
3.4 變速器軸的強度計算與校核 28
3.4.1變速器軸的結構和尺寸 28
3.4.2 軸的校核 30
3.5 軸承的選擇與校核 34
3.5.1 幾種軸承的特點與選擇 34
3.5.2 軸承的校核 36
3.6 變速器同步器的設計 42
3.6.1 同步器的結構 42
3.6.2 同步環主要參數的確定 43
3.7 本章小結 46
結論 47
致謝 48
參考文獻 49
附錄1 50
附錄2 54
- IV -
- IV -
附錄1
變速箱齒輪的設計準則：
由于汽車變速箱各擋齒輪的工作情況是不相同的，所以按齒輪受力、轉速、噪聲要求等情況，應該將它們分為高擋工作區和低擋工作區兩大類。齒輪的變位系數、壓力角、螺旋角、模數和齒頂高系數等都應該按這兩個工作區進行不同的選擇。
高擋工作區：通常是指三、四、五擋齒輪，它們在這個區內的工作特點是行車利用率較高，因為它們是汽車的經濟性擋位。在高擋工作區內的齒輪轉速都比較高，因此容易產生較大的噪聲，特別是增速傳動，但是它們的受力卻很小，強度應力值都比較低，所以強度裕量較大，即使削弱一些小齒輪的強度，齒輪匹配壽命也在適用的范圍內。因此，在高擋工作區內齒輪的主要設計要求是降低噪聲和保證其傳動平穩，而強度只是第二位的因素。
低擋工作區：通常是指一、二、倒擋齒輪，它們在這個區內的工作特點是行車利用率低，工作時間短，而且它們的轉速比較低，因此由于轉速而產生的噪聲比較小。但是它們所傳遞的力矩卻比較大，輪齒的應力值比較高。所以低擋區齒輪的主要設計要求是提高強度，而降低噪聲卻是次要的。
在高擋工作區，通過選用較小的模數、較小的壓力角、較大的螺旋角、較小的正角度變位系數和較大的齒頂高系數。通過控制滑動比的噪聲指標和控制摩擦力的噪聲指標以及合理選用總重合度系數、合理分配端面重合度和軸向重合度，以滿足現代變速箱的設計要求，達到降低噪聲、傳動平穩的最佳效果。而在低擋工作區，通過選用較大的模數、較大的壓力角、較小的螺旋角、較大的正角度變位系數和較小的齒頂高系數，來增大低擋齒輪的彎曲強度，以滿足汽車變速箱低擋齒輪的低速大扭矩的強度要求。以下將具體闡述怎樣合理選擇這些設計參數。
變速箱各擋齒輪基本參數的選擇：
1 合理選用模數：
模數是齒輪的一個重要基本參數，模數越大，齒厚也就越大，齒輪的彎曲強度也越大，它的承載能力也就越大。反之模數越小，齒厚就會變薄，齒輪的彎曲強度也就越小。對于低速擋的齒輪，由于轉速低、扭矩大，齒輪的彎曲應力比較大，所以需選用較大的模數，以保證其強度要求。而高速擋齒輪，由于轉速高、扭矩小，齒輪的彎曲應力比較小，所以在保證齒輪彎曲強度的前提下，一般選用較小的模數，這樣就可以增加齒輪的齒數，以得到較大的重合度，從而達到降低噪聲的目的。
在現代變速箱設計中，各擋齒輪模數的選擇是不同的。例如，某變速箱一擋齒輪到五擋齒輪的模數分別是：3.5；3；2.75；2.5；2；從而改變了過去模數相同或模數拉不開的狀況。
2合理選用壓力角：
當一個齒輪的模數和齒數確定了，齒輪的分度圓直徑也就確定了，而齒輪的漸開線齒形取決于基圓的大小，基圓大小又受到壓力角的影響。對于同一分度圓的齒輪而言，若其分度圓壓力角不同，基圓也就不同。當壓力角越大時，基圓直徑就越小，漸開線就越彎曲，輪齒的齒根就會變厚，齒面曲率半徑增大，從而可以提高輪齒的彎曲強度和接觸強度。當減小壓力角時，基圓直徑就會變大，齒形漸開線就會變的平直一些，齒根變薄，齒面的曲率半徑變小，從而使得輪齒的彎曲強度和接觸強度均會下降，但是隨著壓力角的減小，可增加齒輪的重合度，減小輪齒的剛度，并且可以減小進入和退出嚙合時的動載荷，所有這些都有利于降低噪聲。因此，對于低速擋齒輪，常采用較大的壓力角，以滿足其強度要求；而高速擋齒輪常采用較小的壓力角，以滿足其降低噪聲的要求。
例如：某一齒輪模數為3，齒數為30，當壓力角為17.5度時基圓齒厚為5.341；當壓力角為25度時，基圓齒厚為6.716；其基圓齒厚增加了25%左右，所以增大壓力角可以增加其彎曲強度。
3 合理選用螺旋角：
與直齒輪相比，斜齒輪具有傳動平穩，重合度大，沖擊小和噪聲小等優點?，F(xiàn)在的變速箱由于帶同步器，換擋時不再直接移動一個齒輪與另一個齒輪嚙合，而是所有的齒輪都相嚙合，這樣就給使用斜齒輪帶來方便，因此帶同步器的變速箱大多都使用斜齒輪。
由于斜齒輪的特點，決定了整個齒寬不是同時全部進入嚙合的，而是先由輪齒的一端進入嚙合，隨著輪齒的傳動，沿齒寬方向逐漸進入嚙合，直到全部齒寬都進入嚙合，所以斜齒輪的實際嚙合區域比直齒輪的大。當齒寬一定時，斜齒輪的重合度隨螺旋角增加而增加。承載能力也就越強，平穩性也就越好。從理論上講，螺旋角越大越好，但螺旋角增大，會使軸向分力也增大，從而使得傳遞效率降低了。
在現代變速箱的設計中，為了保證齒輪傳動的平穩性、低噪聲和少沖擊，所有齒輪都要選擇較大的螺旋角，一般都在30°左右。對于高速擋齒輪由于轉速較高，要求平穩，少沖擊，低噪聲，因此采用小模數，大螺旋角；而低速擋齒輪則用較大模數，較小螺旋角。
4合理選用正角度變位：
對于具有良好潤滑條件的硬齒面齒輪傳動，一般認為其主要危險是在循環交變應力作用下，齒根的疲勞裂紋逐漸擴張造成齒根斷裂而失效。變速箱中齒輪失效正是屬于這一種。為了避免輪齒折斷，應盡量提高齒根彎曲強度，而運用正變位，則可達到這個目的。一般情況下，變位系數越大，齒形系數值就越小，輪齒上彎曲應力越小，輪齒彎曲強度就越高。
在硬齒面的齒輪傳動中，齒面點蝕剝落也是失效原因之一。增大嚙合角，可降低齒面間的接觸應力和最大滑動率，能大大提高抗點蝕能力。而增大嚙合角，則必須對一副齒輪都實行正變位，這樣既可提高齒面的接觸強度，又可提高齒根的彎曲強度，從而達到提高齒輪的承載能力效果。但是，對于斜齒輪傳動，變位系數過大，又會使輪齒總的接觸線長度縮短，反而降低其承載能力。同時，變位系數越大，由于齒頂圓要隨之增大，其齒頂厚度將會變小，這會影響齒頂?shù)膹姸取?
因此在現代變速箱的設計中，大多數齒輪均合理采用正角度變位，以最大限度發揮其優點。主要有以下幾個設計準則：
對于低速擋齒輪副來說，主動齒輪的變位系數應大于被動齒輪的變位系數，而對高速擋齒輪副，其主動齒輪的變位系數應小于被動齒輪的變位系數。
主動齒輪的變位系數隨擋位的升高而逐漸xiajiang。這是因為低擋區由于轉速低、扭矩大，齒輪強度要求高，因此需采用較da的變位系數。
各擋齒輪的總變位系數都是正的（屬于角變位修正），而且隨著擋位的升高而逐漸減小?？傋兾幌禂?shù)越小，一對齒輪副的齒根總的厚度就越薄，齒根就越弱，其抗彎強度就越 低，但是由于輪齒的剛度減小，易于吸收沖擊振動，故可降低噪聲。而且齒形重合度會增加，這使得單齒承受最大載荷時的著力點距齒根近，使得彎曲力矩減小，相當于提高了齒根強度，這對由于齒根減薄而消弱強度的因素有所抵消。所以總變位系數越大，則齒根強度越高，但噪聲則有可能增大。因此高速擋齒輪要選擇較小的總變位系數，而低速擋齒輪則必須選用較大的總變位系數。
5 提高齒頂高系數：
齒頂高系數在傳動質量指標中，影響著重合度，在斜齒輪中主要影響端面重合度。由端面重合度的公式可知，當齒數和嚙合角一定時，齒頂圓壓力角是受齒頂高系數影響的，齒頂高系數越大，齒頂圓壓力角也越大，重合度也就越大，傳動也就越平穩。但是，齒頂高系數越大，齒頂厚度就會越薄，從而影響齒頂強度。同時，從最少不根切齒數公式來看，齒頂高系數越大，最少不根切齒數就會增加，否則的話，就會產生根切。因此，在保證不根切和齒頂強度足夠的情況下，增大齒頂高系數，對于增加重合度是有意義的。
因此在現代變速箱的設計中，各擋齒輪的齒頂高系數都選擇較大的值，一般都大于1.0，稱為細高齒，這對降低噪聲，增加傳動平穩性都有明顯的效果。對于低速擋齒輪，為了保證其具有足夠的齒根彎曲強度，一般選用較小的齒頂高系數；而高速擋齒輪，為了保證其傳動的平穩性和低噪聲，一般選用較大的齒頂高系數。
以上是從模數、壓力角、螺旋角、變位系數和齒頂高系數這五個方面去獨立分析齒輪設計趨勢。實際上各個參數之間是互相影響、互相牽連的，在選擇變速箱的參數時，既要考慮它們的優缺點，又要考慮它們之間的相互關系，從而以最大限度發揮其長處，避免短處，改善變速箱的使用性能。
附錄2
Gearbox design criteria:
As the automobile gearbox stall the work gear is not the same, so according to gear force, speed, noise requirements, etc., they should be divided into high and low-end work area work area two broad categories. Gear modification coefficient, pressure angle, helix angle, modulus and Addendum coefficient and so on should be based on the work areas of these two different options.
High-grade work area: usually refers to the three, four, five-speed gears, they work in this area is characterized by a higher utilization rate of traffic, because they are economical car stalls. In the high-end gear working area than the higher speed, so easy to have a greater noise, especially the growth rate of transmission, but their force was small, the intensity of stress values are relatively low, so strength margin, so even after weaken the strength of some small gear, gear matching is also applicable within the framework of life. Therefore, in high gear the work of the major design requirements for the region is to reduce noise and ensure a smooth transmission, while the intensity is only the second factor.
Low-grade work area: usually refers to the first, second and reverse gears, they work in this area is characterized by low utilization rate of traffic, working time is short, and their speed is relatively low, so the noise generated due to rotational speed is relatively small. But the moment they are transmitted is larger, tooth stress values are relatively high. Therefore, the main gear low area design requirements is to improve the strength, while the noise reduction is secondary.
In the high-end work area, through the use of smaller modulus, the smaller the pressure angle, the larger the helix angle, the smaller is the angle variable coefficient and a larger Addendum coefficient. Noise ratio by controlling the sliding friction of indicators and control of noise indicators, and a reasonable selection of the total coincidence coefficient, reasonable distribution of end-of coincidence degree and axial coincidence degree, in order to meet the design requirements of modern transmissions, to reduce the noise, transmission of the most stable good results. In the low-grade work area, through the selection of the larger modulus, the larger pressure angle, the smaller helix angle, the larger is the angle variable coefficient and a smaller Addendum coefficient,
To increase the low-end gear bending strength to meet the low-speed auto gearbox gear high-torque low strength requirements. The following will specifically set out what a reasonable selection of these design parameters.
Transmission gear basic parameters of the file options:
A reasonable choice Modulus:
Modulus is an important basic parameters of gears, the greater the modulus, the greater the tooth thickness, the greater the gear bending strength, the greater its carrying capacity. On the contrary modulus smaller tooth thickness will be thinner, thus the smaller the gear bending strength. For the low-profile gear, due to the low rotational speed, torque, gear bending stress relatively large, so we need to use a larger module in order to ensure its strength demands. The high gear gear, due to high speed, torque is small, gear bending stress is relatively small, so ensure that the premise of gear bending strength, generally use a smaller modulus, so that you can increase the number of teeth in order to obtain a larger coincidence degree
So as to achieve noise reduction purposes.
In modern transmission design, each gear module file option is different. For example, a transmission gear to file a five-speed gear module are: 3.5; 3; 2.75; 2.5; 2; thus changing the modulus of the same or a module over the past few pull not open situation.
2 rational selection pressure angle:
When a gear tooth modulus and determined, gear pitch circle diameter also identified, while the gear involute base circle depends on the size of the base circle size of the impact angle under pressure again. For the same pitch circle of gear, if it is the pressure angle of its sub-degree circle is different from the base circle is different. When the pressure angle, the larger, the base circle diameter of the smaller, more curved involute, tooth tooth root will be thicker and larger radius of curvature of tooth surface, which can increase the tooth bending strength and contact strength. When reducing the pressure angle, the base circle diameter will be larger, the involute tooth profile will change some of the flat, tooth root thinning, tooth surface radius of curvature smaller,
Which makes the tooth bending strength and contact strength will decrease, but as the pressure angle decreases, increase the degree of coincidence gears, reducing the tooth stiffness, and can reduce the time of entry and exit mesh dynamic load, All of these are beneficial to reduce the noise. Therefore, for low-profile gear, often with a larger pressure angle, in order to meet the strength requirements; while the high gear gear often used a smaller pressure angle, in order to meet their noise reduction requirements.
For example: a gear module 3, teeth 30, when the pressure angle of 17.5 degrees tooth thickness of 5.341 base circle; when the pressure angle of 25 degrees, the base circular tooth thickness of 6.716; its base circle tooth thickness increased about 25%, so increase the pressure angle can increase its bending strength.
A reasonable choice of three helix angle:
Compared with the spur gear, helical gear with a transmission smooth, coincidence degree, the impact of small and low noise advantages. As with the current transmission synchronizer, the shifter is no longer directly moving a gear meshing with another gear, but all of the gears are meshing phase, disturbing the convenient use of helical gears, so the transmission with a synchronizer Most of all use helical gears.
Because the characteristics of helical gears and decided the entire tooth width is not the same time, all entered the mesh, but first be entered at one end of tooth meshing with the tooth of the drive, along the tooth width direction is gradually enter the mesh, until the entire tooth width have to enter into mesh, so the actual meshing helical gear spur gear than a large area. When the tooth width is constant, helical gear with helix angle degree of coincidence increases. Carrying capacity of the stronger, the better smoothness. In theory, the helix angle the bigger the better, but the helix angle increases, the axial pitch will also increase, making the transfer efficiency decreased.
In modern transmission design, in order to ensure smooth gear drive, low noise and low impact, all the gears should choose a larger helix angle, generally in about 30 °. For high-speed stall speed due to a higher gear, for a stable, low impact, low-noise, so a small modulus, large helical angle; while low-profile gear you use a larger modulus, the smaller spiral angle.
4 is a reasonable choice of the angle deformation:
For the good of the hardened gear lubrication condition is generally believed that the main danger is in the loop under the action of alternating stress, the tooth root fatigue cracks caused by the gradual expansion of the tooth root fracture and failure. Transmission in gear failure is a part of this. In order to avoid tooth fracture, it should enhance tooth root bending strength, while the use of positive deflection, you can achieve this goal. Under normal circumstances, variable coefficient the greater the coefficient the smaller the tooth, tooth bending stress on the smaller, the higher the tooth bending strength.
In the hardened gear transmission, the tooth surface pitting peel off one of the reasons is also a failure. Increased engagement angle, which reduces the contact between the tooth surface stress and maximum slip rates, can greatly enhance the pitting corrosion resistance capabilities. The increased pressure angle, it must be practiced on a gear is changed bits, thereby enhancing the tooth surface contact strength, but also improve the bending strength of tooth roots to achieve the effect of improving the carrying capacity of gears. However, for helical gear drive, variable coefficient is too large, but also the total tooth will shorten the length of contact line, but reduce its carrying capacity. Meanwhile, the variable coefficient greater, due to tooth tip should be even greater, the tooth tip thickness will be smaller,
This will affect the strength of the top gear.
Therefore, in modern transmission design, most of the gears are a reasonable angle of deflection is used in order to maximize its advantages. Mainly in the following design guidelines:
For the low-profile gear pair, the active gear variable coefficient should be larger than the passive gear modification coefficient, while for high-speed file gear pair, which take the initiative to gear modification coefficients should be less than the passive gear modification coefficient.
Active gear modification coefficient increases gradually with stalls xiajiang. This is because the low-grade area due to the low rotational speed, torque, gear strength with high requirements, therefore need to adopt a more da variable coefficient.
Gear of the total variation of all files coefficient is positive (of the angle deflection amended), and along with the increase of stalls gradually decreased. The smaller the total variation coefficient, a pair of gear pairs of the total thickness of the tooth root more thin, tooth root more weak, its lower bending strength, but because of reduced tooth stiffness, easy to absorb shock and vibration, so can reduce the noise. And the degree of tooth overlap will increase, which makes a single tooth to withstand the maximum load when the focus on pitch near the tooth root, making bending moment decrease is equivalent to increasing strength of the tooth root, which is due to thinning and weakening of tooth root strength factor has been offset. Therefore, the greater the total variation coefficient, then the tooth root strength of the higher
But the noise is likely to increase. So high gear gear to choose a smaller total variation coefficient, while the low-profile gear, you must use a larger total variation coefficient.
Addendum 5 to the factor:
Addendum coefficient of transmission quality index, the impact of focus on adaptation, the main impact in the helical gear face of coincidence degree. End coincidence degree from the formula we can see, when the number of teeth and meshing a certain angle, the tooth tip pressure angle is subject to the impact of Addendum coefficient, Addendum coefficient the greater the addendum circle the greater the pressure angle, coincidence degree also The larger drive is also more stable. However, Addendum coefficient the greater the thickness of the top teeth will be thinner, thereby affecting the intensity of the top teeth. At the same time, from at least a few formula Cutting is not the root point of view, the greater the Addendum coefficient, at least not the root Cutting the number will increase, otherwise, it will generate the root cutting. Therefore,
In the guarantee not to cut the root and the tooth top of the case of sufficient strength, increasing the Addendum coefficient, for increasing the degree of coincidence is meaningful.
Therefore, the design of a modern gearbox, each gear tooth profile the top choice of high coefficients are greater value, generally greater than 1.0, known as fine a high-tooth, which is to reduce noise, increase the transmission has a significant effect of Stationarity . For the low-profile gear, in order to ensure that it has enough tooth root bending strength, generally choose the smaller Addendum coefficient; while the high gear gear, in order to ensure its smooth transmission and low noise, generally choose the larger Addendum factor.
The above is from the module, pressure angle, helix angle, addendum modification coefficient and the coefficient of these five areas to an independent analysis of gear design trends. In fact between the various parameters influence each other mutually implicated, the choice of transmission parameters, it is necessary to take into account their strengths and weaknesses, but also take into account the relationship between them in order to maximize its strengths and weaknesses and to improve the use of transmission performance.
- 10 -