空心坯減徑機副減速器設計

空心坯減徑機副減速器設計,空心,坯減徑機副,減速器,設計 摘 要 由于科技的進步和人們生活水平的提高，生產設備和產品的更新，鋼材不斷提高產品產量和質量，提高生產率，降低原材料和能源的消耗及產品的成本提出了更高的要求。這也是和軋鋼設備制造水平有關的重型機械制造和自動控制等科學技術的發展有密切關系., 本文首先對設計方案進行了介紹；并介紹了電動機的選擇方法、箱體的設計、軸的設計、齒輪的設計、鍵的選擇等，然后簡要介紹了減速器裝配的一些相關知識及技術說明;最后列出了設計過程中翻閱及參考過的文獻。 關鍵詞： 軋鋼機 減速器 設計方案 參考文獻 Abstract As a result of the technical progress and the people living standard enhancement, the production equipment and the product renewal, the steel products enhance the volume of output and the quality unceasingly, enhances the productivity, reduced raw material and the energy consumption and the product cost set a higher request.This also is and the rolling mill equipment manufacture level related heavy duty machinery manufacture and the automatic control and so on the science and technology development has the close relation. This article first has carried on the introduction to the design proposal; And introduced the electric motor choice method, the box body design, the axis design, the gear design, the key choice and so on, then introduced briefly the reduction gear assembles some correlation knowledge and technical order; Finally has listed in the design process glances through and has referred the literature. Key word: Mill reduction gear design proposal reference 目 錄 摘要………………………………………………………………………………Ⅰ ABSTRACT………………………………………………………………………Ⅱ 第一章、傳動方案的擬定及說明 1.1傳動方案…………………………………………………………… 1 第二章、電動機的選擇 2.1電動機的選擇……………………………………………………… 2 第三章、鑄造減速器箱體 3.1 鑄造減速器箱體主要結構尺寸………………………………… 4 第四章、軸的設計計算 4.1 高速軸的計算…………………………………………………… 5 4.2 低速軸1的計算…………………………………………………… 7 4.3 中間軸1的計算…………………………………………………… 9 4.4 低速軸2的計算…………………………………………………… 11 4.5 中間軸2的計算…………………………………………………… 13 第五章、滾動軸承的選擇及計算 5.1 滾動軸承的選擇及計算……………………………………………14 第六章、傳動件的設計計算 6.1 選精度等級、材料及齒數……………………………………… 15 第七章 連接件的選擇及潤滑 7.1 鍵連接的選擇及校核計算……………………………………… 19 7.2 連軸器的選擇…………………………………………………… 19 7.3 減速器附件的選擇……………………………………………… 20 7.4 潤滑與密封……………………………………………………… 20 第八章 減速器裝配圖的繪制及技術說明………………………………20 8.1 裝備圖的總體規劃……………………………………………… 21 8.2 繪制過程………………………………………………………… 21 8.3 完成裝配圖……………………………………………………… 23 8.4 相關技術說明…………………………………………………… 23 結語……………………………………………………………………………… 24 參考資料目錄…………………………………………………………………… 25 致謝……………………………………………………………………………… 26 III