基于單片機控制的開關電源資料

基于單片機控制的開關電源資料,基于,單片機,控制,節制,開關電源,資料 目 錄 引言 ...........................................................................................................................................1 1 概述 ....................................................................................................................................1 1.1 課題來源及意義.................................................................................................................1 1.2 課題基本要求.....................................................................................................................2 1.3 相關背景介紹.....................................................................................................................2 2 基于單片機的數控直流電源方案設計 ...................................................................2 2.1 方案設計.............................................................................................................................3 2.1.1 方案 1：開關穩壓電源..................................................................................................3 2.1.2 方案 2：線性穩壓電源....................................................................................................4 2.2 方案論證.............................................................................................................................5 2.2.1 方案一分析......................................................................................................................5 2.2.2 方案二分析......................................................................................................................5 3．硬件電路設計..................................................................................................................5 3.1 主電源電路設計.................................................................................................................6 3.1.1 變壓器的選擇.................................................................................................................6 3.1.2 整流濾波電路.................................................................................................................7 3.1.3 穩壓調壓電路.................................................................................................................8 3.1.4 擴流電路.........................................................................................................................8 3.2 副電源電路設計.................................................................................................................9 3.3 控制部分電路設計...........................................................................................................10 3.3.1 A/D 及 D/A 轉換電路....................................................................................................11 3.3.2 校正部分電路...............................................................................................................14 3.3.3 鍵盤及數碼管顯示電路...............................................................................................15 4 軟件設計 ...........................................................................................................................17 4.1 軟件介紹...........................................................................................................................17 4.1.1 Protel 99 SE...............................................................................................................18 4.1.2 Keil uVision2.............................................................................................................18 4.2 編程思想...........................................................................................................................19 4.2.1 鍵盤和數碼管掃描子程序...........................................................................................19 4.2.2 ADC0809 轉換子程序....................................................................................................20 4.2.3 DAC0832 轉換子程序....................................................................................................21 4.2.4 中斷定時處理程序設計..................................................................................................21 4.2.5 數碼顯示子程序............................................................................................................22 4.2.6 溫度傳感器的電壓校正...............................................................................................22 5 系統調試 ...........................................................................................................................22 5.1 硬件模塊調試...................................................................................................................22 5.1.1 電源部分技術指標測試...............................................................................................22 5.1.2 電源輸出電壓、電流范圍測試....................................................................................24 5.1.3 硬件模塊調試小結.......................................................................................................25 5.2 軟件模塊調試...................................................................................................................25 5.2.1 鍵盤按鍵控制及數碼管顯示.......................................................................................25 5.2.3 數字溫度傳感器 DS1820 的電壓校正.........................................................................28 5.2.4 軟件模塊調試小結.......................................................................................................28 6. 技術指標及使用方法 ...................................................................................................29 7 結論 ..................................................................................................................................29 謝辭 .........................................................................................................................................30 參考文獻 ................................................................................................................................31 附錄 .........................................................................................................................................31