無凸緣圓筒形件-氣瓶沖壓成形工藝及模具設計【落料拉深復合模、縮口模含2副模具24張CAD】
【需要咨詢購買全套設計請加QQ1459919609】圖紙預覽詳情如下:
目 錄1 緒 論 ................................................................11.1 國內模具的現狀和發展趨勢 ...................................................................................11.1.1 國內模具的現狀 .............................................................................................11.1.2 國內模具的發展趨勢 ..................................................................................21.2 國外模具的現狀和發展趨勢 ................................................................................31.3 深圓筒拉深件模具設計與制造方面 ....................................................................41.3.1 深圓筒拉深模具設計的設計思路 ................................................................41.3.2 深圓筒拉深模具設計的進度 .........................................................................41.4 縮口工件模具設計與制造方面 ............................................................................42 汽瓶落料拉深復合模的設計 ..............................................52.1 工件工藝分析 ...........................................................................................................52.2 工藝方案確定 ...........................................................................................................52.2.1 計算縮口因數 .................................................................................................62.2.2 計算縮口前毛胚高度 H.................................................................................62.2.3 確定拉深次數 .................................................................................................62.3 進行必要的計算 .......................................................................................................82.3.1 各次拉深工序件尺寸的確定 .........................................................................82.3.2 壓邊力和拉深力 .............................................................................................92.3.3 工序壓力,初選壓力機 ..............................................................................112.3.4 模具工作部分的計算 ..................................................................................112.4 模具的總體結構設計 .............................................................................................132.4.1 模具類型的選擇 ...........................................................................................132.4.2 定位方式的選擇 ...........................................................................................132.4.3 卸料、出件方式的選擇 ...............................................................................132.4.4 導向方式的選擇 ...........................................................................................132.5 主要零部件的設計 ................................................................................................132.5.1 落料凹模結構設計與標準化 .......................................................................132.5.3 凸凹模(落料凸模、拉深凹模) ...............................................................162.5.4 壓邊圈 ...........................................................................................................172.5.5 確定凸模的通氣孔 .......................................................................................172.5.6 推件塊 ...........................................................................................................172.5.7 選用模架、確定閉合高度及總體尺寸 .......................................................182.6 模具總裝圖 .............................................................................................................19 2.7 沖壓設備的選定 .....................................................................................................193 汽瓶縮口模的設計 .....................................................253.1 必要的工藝計算 .....................................................................................................253.1.1 縮口力,初選壓力機 ...................................................................................253.2 模具總體結構設計 .................................................................................................253.2.1 模具類型的選擇 ...........................................................................................253.2.2 定位方式的選擇 ...........................................................................................253.2.3 卸料、出件方式的選擇 ...............................................................................253.2.4 導向方式的選擇 ...........................................................................................263.3.1 縮口凹模結構設計 .......................................................................................263.3.2 外支撐塊設計 ...............................................................................................273.3.3 卸料裝置的設計與標準化 ...........................................................................283.3.4 模柄 ...............................................................................................................293.3.5 打桿 ...............................................................................................................293.3.6 標準模架的選用 ...........................................................................................303.3.7 連接件選用與標準化 ...................................................................................303.4 模具總裝圖 .............................................................................................................313.5 沖壓設備的選定 .....................................................................................................31沖壓模具零件加工工藝的編制凹模加工工藝過程 ...................................................32結 束 語 ...............................................................34致 謝 .................................................................35參考文獻 ...............................................................37