購買設計請充值后下載,,資源目錄下的文件所見即所得,都可以點開預覽,,資料完整,充值下載就能得到。。?!咀ⅰ浚篸wg后綴為CAD圖,doc,docx為WORD文檔,【有不明白之處,可咨詢QQ:1304139763】
鹽城工學院本科生畢業設計說明書 2009 基于 pro e 的接線墊片級進模的設計及凸模的加工仿真 摘要 級進模精度高 壽命長 其工作元件常采用高速鋼或硬質合金鋼制 造 適用于制件的大批量生產 制件質量可靠 穩定 及制件尺寸的一致性好 級進模結構復雜 制造精度高 調試 維修困難 價格昂貴 本文作者從工藝 的合理性出發 分析了接線墊片精度特點 以及在加工過程中的控制點 然后 在滿足加工精度的基礎上充分考慮節約成本確定了接線墊片最優化的沖裁加工 工序 緊接著通過熟悉各類模具的加工特點及內部結構 完成模具總體結構分 析 隨后作者進行毛坯尺寸 排樣 工序尺寸 沖壓壓力 壓力中心 模具工 作部分尺寸等工藝計算 力爭以最好的性價比設計了模具各零件的結構及裝配 關系 在此基礎上確定模具的外形 完成了裝配圖和非標準的零件圖 最后確 定壓力機類型及主要參數 關鍵詞 級進模 排樣 壓力機 鹽城工學院本科生畢業設計說明書 2009 Designing for wiring pads by progressive die based on pro e and the simulation of core plate Abstract Progressive Die with high precision long life its components are often used high speed steel and carbide steel what is applicable to the high volume production Products have good quality stability and consistency of a good sized parts Progressive Die with complex structure and demands high precision manufacturing commissioning maintenance difficulties which is very expensive Author of this text proceed from rationality of the craft analyse character of the and the control point in the course of processing Consider and economize cost confirm wiring pads blanking that shelf optimizes most process the process fully on the basis of satisfying the machining accuracy And then pass the processing characteristic familiar with all kinds of moulds and inside structure Finish the ensemble architecture analysis of the mould Author carry on blank size arrange kind process size punching pressure pressure in the center afterwards mould work some size etc craft calculate Strive to design the structure of every part of the mould and assembly relation with the best cost performance Confirm the appearance of the mould on this basis has finished the installation diagram and non standard part picture Confirm the type of the press and main parameter finally Key words Progressive Die Arrange kind automatic punching machine