購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，有不明白之處，可咨詢QQ:1304139763
洗發水瓶蓋注塑成型工藝及模具設計 摘 要 本次模具設計的內容是 洗發液瓶蓋注塑模的設計 這個制品的結構近似一 個殼體 主蓋與其上面的小蓋以鉸鏈相連 打開后 小蓋固定在一特定位置 合上 后與主蓋成一整體 設計內容是從零件的工藝分析開始的 根據工藝要求來確定設 計的大體思路 其開始是從零件的材料選擇 接下是成型參數 密度 收縮率的確 定 模具種類與模具設計的關系 塑件的尺寸精度與結構 注射機的選擇 模具設 計有關尺寸的計算 包括模具行腔型芯的計算及其公差的確定 注塑機參數的校核 模具結構設計 模具冷卻 加熱系統計算 注射模標準件的選用及總裝技術要求等 內容 其中模具結構設計是這次設計的主要內容 其內容包含了模具的分型面選擇 主流道及分流道的設計與布局 推出機構導向機構 鉸鏈的設計等一系列模具的重要 零部件的設計加工方法和加工注意要點 塑料瓶蓋的材料選用聚丙烯 首先用 UG 進行洗發水瓶蓋的三維造型 利用 CAD CAE 作出輔助分析 通過查閱各種資料 完成包括形狀及尺寸方面的數據運算 然后根據洗發水瓶蓋的結構特點設計了模具的型芯 型腔 脫模及整體結構 此模 具的結構較為復雜 動模和定模都采用了鑲拼結構 由于生產批量較大 采用一模 兩腔 對排的布置方式 由于聚丙烯對熱較敏感 且此塑件的壁厚較薄 經過計算 此設計可以不必加設冷卻水道 此外 為了縮短模具的生產周期 提高生產率 本 設計在很多地方采用標準件 例如模架 導柱導套 關鍵詞 洗發液瓶蓋 注塑模 鉸鏈 PC I Shampoo Bottle Cap Injection Molding Process and Mold Design ABSTRACT The mold design and the contents of the shampoo bottle injection mold design The structure of the products approximate a shell the main cover their above cover is connected to the hinge open small cover at a particular location close the main cover as a whole Design from parts of the process began to determine the design according to process requirements of the general idea Start is selected from the parts of the materials took over the molding parameters density shrinkage to determine the types of mold and die design the choice of dimensional accuracy and structural plastic parts injection machine mold design and calculation of the size including computing and its tolerance of the cavity mold line core the checking of the parameters of injection molding machines and mold structure design mold cooling heating system calculation injection mold standard parts selection andassembly of technical requirements and content Which mold structure design is the main content of the design contains the mold parting surface of choice sprue and shunt design and layout the introduction of agency oriented institutions the important parts of the hinge design and a series of molds design and processing methods and processing points to note Shampoo bottle is made of polypropylene First Pro E is used to form three dimensional shape of the cap of shampoo bottle CAD CAE makes an assisted analysis After reading a variety of available information the data computation of the shape and size could be completed And then the cap of shampoo bottle in accordance with the structural characteristics of the design of the mold the core cavity and the overall structure of molding The structure of this mold is rather complex the dynamic and determined mold are both adopted composite structure Due to the larger quantities of production A two mode cavity is used the arrangement of row As the polypropylene is more sensitive to heat and the thinner wall thickness of plastic parts in this design can be calculated do not need additional cooling water In addition in order to shorten the production cycle of mold and improve productivity the design adopts standard in many places such as mold lead guide sets of columns KEY WORDS shampoo bottle cap injection mold hinge PC