三級齒輪減速器殼體的應力分析與優化設計外文文獻翻譯、中英文翻譯、外文翻譯

三級齒輪減速器殼體的應力分析與優化設計外文文獻翻譯、中英文翻譯、外文翻譯,三級,齒輪,減速器,殼體,應力,分析,優化,設計,外文,文獻,翻譯,中英文 英文原文 Applied Mechanics and Materials Vol.658(2014)pp 183-188 Submitted: 29.04.2014 (2014) Trans Tech Publications, Switzerland Revised : 22.05.2014 Doi:10.4028/www.scientific.net/AMM.658.183 Accepted: 27.05.2014 Stress Analysis and Optimal Design of the Housing of a Three-Stage Gear Reducer COJOCARU Vasile 1,a*, KORKA Zoltan-losif 1,b And MICLOSINA Calin-Octavian 1,c 1”Eftimie Murgu” University of Resita, Faculty of Engineering and Management, Department of Mechanics and Materials Engineering, Traian Vuia Square, No.1~4, 320085 Resita, Romania a*v.cojocaru@uem.ro, bz.korka@uem.ro, cc.miclosina@uem.ro Keywords: gear reducer; housing stress; displacement; finite element analysis Abstract. The design of the housings of the gear reducers is made, usually, using empirical equations based on the center distance (the distance between shafts). These equations can lead to inappropriate stresses distribution and inadequate material consumption at the final product. In the manufacturing of large series and in the manufacturing of the gear reducers/ gearboxes with large dimensions it is necessary an optimization of the housing dimensions. The use of the finite element analysis in this process, combined with experimental researches, can generate significant improvements. The paper is focused on the analysis of stresses distribution and displacements on the housing of a two-stage helical gear reducer with parametric dimensions and loads. The housing is subjected to a static finite element study. The optimization process aimed to minimize the total weight of the housing. The next features were submitted to dimensional changes: the thickness of the housing walls and the thickness of the ribs. The results presented as diagrams of stresses and displacements distributions show real opportunities to reduce the total weight of the housing and the material consumption. Introduction One of the major trends of the mechanical engineering is the design of compact equipment with lower mass and lower material consumption. On the gear reducers/ gear boxes this goal can be reach by an optimal design of the gearing [1,2] and of gear supporting elements (shafts, housing). The design process of the helical gears reducers involves the calculations of the main parameters that influence the dimensions of the housing of the gear reducer: the center distance, the diameter of the bearings, the outside diameters of the gearwheels, the shafts lengths. The other dimensions of the housing are defined by empirical equations. In the scientific literature of the gear engineering are listed various equations for the calculus of the thickness of the housing walls, δ [mm]. These equations are based usually on the overall length (l) of the housing [3]: δ=(0.004...0.0005)?l+4，or on the total center distance (a) of the reducers[4]: δ=0.025?a+5. The value calculated for δ, is used in the calculus of the dimensions of the housing ribs and flanges [3]. This design algorithm can generate the oversizing of housing, increasing the mass of the reducer and the manufacturing costs. These conclusions lead to the necessity of optimization of the design process of the housing. The complexity of the housing geometry makes difficult to accomplish the determination of the strains and stresses by analytical relations. Evaluation of the strains and stresses by experimental methods is expensive and it is difficult to extrapolate the results of the measurements. The use of the finite element simulations, validated through experimental researches, can generate solutions for a proper stress distributions and an optimal design of the gear housing [5,6]. The use of parametric models in the finite element analysis allows the rapid changes of the dimensions and the loads applied to the part. Thereby the analysis can be run for a wide range of typo-dimensions, decreasing the time needed to release a new product. The current research aims to highlight the possibilities of improvement of the housing of a two-stage helical gear reducer using finite element simulations. Conclusions The results of the FEM simulations performed on the housing of a two-stage gear reducer submitted to static loads show that the geometry and dimensions obtained from empirical equations can be optimized. This optimization can be made based on the FEM simulations validated by experimental measurements. The maximum values of the Von Misses stresses obtained for the geometries analyzed are far below the allowable limit of the steel used in simulations. The maximum values of displacements are within acceptable limits, however shall be deemed that these displacements can accentuate the housing vibrations in the dynamic loads conditions. This observation leads to the conclusion that the criterion of rigidity should be a priority in the designing process of the housing. The charts of stresses and displacements distributions allow the identification of the weak areas. The geometrical changes of the housing made in these areas generate adequate solutions with the best ratio between the mass decrease and the stress/displacement increase. Acknowledgment The work has been funded by the Sectoral Operational Programme Human Resources Development 2007-2013 of the Ministry of European Funds through the Financial Agreement POSDRU/159/1.5/S/132395. References [1] L. Tudose et al., Optimal design of two-stage speed reducer using two-phase evolutionary algorithm, International Journal of Mechanics, Issue 3, Volume 2, 2008, pp.55-66. [2] O. Buiga, C.O. Popa, Optimal Mass Design of a Single-Stage Helical Gear Unit with Genetic Algorithms, Proceedings of the Romanian Academy, Series A. Vol. 13, No.3/2012,pp.243-250. [3]D. Muhs,H. Wittcl,D. Jannasch, Roloff/Matck - Machinc Elements, in Romanian, Vol. II, Matrix Rom, ISBN 978-973-755-412-3, Bucuresti, 2008. [4] I. Palade et al.,Gear reducers, in Romanian,Dunarea de Jos University,Galati,2008, available online at http://www.om.ugal.ro/om/biblioteca. [5] M. Davis et al., Designing for Static and Dynamic Loading of a Gear Reducer Housing with FEA. Power Transmission Engineering Magazine, February 2010, available at www.powertransmission.com,pp.32-37. [6] S.M. Patil, S.M, Pise, Modal and Stress Analysis of Differential Gearbox Casing with Optimization, Int. Journal of Engineering Research and Applications, ISSN: 2248-9622, Vol.3,Issue 6, Nov-Dec 2013. pp.188-193. [7] V. Cojocaru, Z. Korka, C. Miclosina, Influence of the Mesh Parameters on Stresses and Strains in FEM Analysis of a Gear Housing, Analele Universitatii Eftimie Murgu, Fascicula I, anul XX, no.2, 2013, ISSN 1453 - 7397,pp.47-52. [8] S.Radzevich,Dudley’s Handbook of Practical Gear Design and Manufacture, CRC Press, NewYork,2012, ISBN: 978-1-4398-6602-3. [9] E.J.Hearn, Mechanics of Materials, Third Edition, Blutterworth Heinemann, Oxford, 2000. [10]G.X. Zhang, E. Rigaud, J.C. Pascal, J. Sabot, Gearboxes: Indirect Identification of Dynamic Forces Transmitted to Housing Through Bearings, 4th World Congress on Gearing and Power Transmission,Paris, France, 1999. 中文譯文 三級齒輪減速器殼體的應力分析與優化設計 發表于應用力學與材料學報658期，由Vasile, Zoltan Losif和Calin Octavian編寫，由瑞士Trans Tech出版物出版 關鍵詞:減速器，殼體，應力，位移，有限元分析。 摘要：齒輪減速器箱體的設計，通常采用基于中心距(軸間距離)的經驗公式。這些方程會導致在最終產品有著不適當?shù)膽Ψ植己筒怀浞值牟牧舷?。在大批量生產和大尺寸齒輪減速器/變速箱的生產中，必須對箱體尺寸進行優化。在這個過程中使用有限元分析，結合實驗研究，可以產生顯著的改進。本文對具有參數尺寸和載荷的兩級斜齒輪減速器殼體的應力分布和位移進行了分析。該殼體進行了靜力有限元研究。優化過程的目標是使外殼的總重量最小。下一個特征描述了尺寸的變化:減速器箱體的厚度和肋的厚度。應力和位移分布的圖表結果，顯示了減少箱體的總重量和材料消耗的真實情況。 介紹： 機械工程的主要趨勢之一是設計出質量更小、材料消耗更低的緊密型設備。在齒輪減速器/齒輪箱上，這一目標可以通過齒輪[1,2]和齒輪支撐元件(軸，外殼)的優化設計來實現。 斜齒輪減速器的設計過程中涉及到影響減速器殼體尺寸的主要參數的計算：中心距離，軸承的直徑，齒輪外徑，軸的長度。箱體的其他維度是由經驗方程定義的。 在齒輪工程的科學文獻中列出了計算殼體壁厚度的各種公式，δ [mm]. 這些方程式通常以殼體的總長度(l)為基礎[3]: δ=(0.004...0.0005)?l+4，或在減速器的總中心距離(a)上[4]: δ=0.025?a+5。計算δ值，用于計算箱體肋和法蘭盤[3]的尺寸。該設計算法可能產生箱體過大，增大減速器的質量和制造成本的問題。這些結論引出了對箱體設計過程進行優化的必要性。 由于殼體幾何形狀的復雜性，很難通過解析關系來確定應力和應變。用實驗方法評估應變和應力是昂貴的，而且很難推斷測量結果。使用有限元模擬，通過實驗研究驗證，可以產生適當?shù)膽Ψ植己妄X輪殼的優化設計的解決方案[5,6]。在有限元分析中參數化模型的使用允許快速變化的尺寸和載荷應用到零件。因此，該分析過程可以針對較為廣泛的尺寸進行，從而減少發布新產品所需的時間。目前的研究旨在強調利用有限元模擬改進兩級斜齒輪減速器外殼的可能性。 總結： 對靜載荷作用下的兩級減速器殼體進行了有限元仿真，結果表明，根據經驗方程得到的殼體幾何尺寸是可以優化的。這種優化可以在有限元模擬和實驗測量的基礎上進行。所分析的幾何形狀的最大應力值遠低于模擬中使用的鋼的允許極限。最大位移值在可接受的范圍內，但應認為這些位移在動荷載條件下會加重殼體振動。這一觀察得出的結論是，剛度標準應優先考慮箱體的設計過程中。應力和位移分布圖允許識別薄弱區域。在這些區域中箱體的幾何變化產生了適當?shù)慕鉀Q方案，質量下降和應力/位移增加之間的最佳比例。