ZL50裝載機總體及工作裝置設計
購買設計請充值后下載,,資源目錄下的文件所見即所得,都可以點開預覽,,資料完整,充值下載可得到資源目錄里的所有文件。。?!咀ⅰ浚篸wg后綴為CAD圖紙,doc,docx為WORD文檔,原稿無水印,可編輯。。。帶三維備注的都有三維源文件,由于部分三維子文件較多,店主做了壓縮打包,都可以保證打開的,三維預覽圖都是店主用電腦打開后截圖的,具體請見文件預覽,有不明白之處,可咨詢QQ:1304139763
目 錄
一、工件工藝性分析 2
二、拉深工藝及拉深模有設計 2
1、 設計要點 2
2、 有凸緣圓筒形件的拉深方法及工藝計算 3
3、 寬凸緣圓筒形件的工藝計算要點 4
4、拉深凸模和凹模的間隙 5
5、拉深凸模,凹模的尺寸及公差 6
6、凹模圓角半徑?rd 7
7、凸模圓角半徑rp 7
三、沖裁工藝及沖裁模具的設計 8
1、凸模與凹模刃口尺寸的計算 8
2、凸、凹模刃口尺寸的計算方法 8
四、模具的其它零件 13
五、壓力機的選擇 19
六、主要組件的裝配 21
七、模具的工作過程 23
蓋冒墊片設計說明書
一、工件工藝性分析
如右圖1所示:工件為有凸緣圓筒形零件,且在凸緣上均勻分布4個相同的孔。故可得知此工件為:落料拉深沖孔所得,其加工工藝過程為:落料-拉深-沖孔,各尺寸關系如圖1所示
二、拉深工藝及拉深模有設計
1、 設計要點
設計確定拉深模結構時為充分保證制件的質量及尺寸的精度,應注意以下幾點
1) 拉深高度應計算準確,且在模具結構上要留有安全余量,以便工件稍高時仍能適應。
2) 拉深凸模上必須設有出氣孔,并注意出氣孔不能被工件包住而失去作用。
3) 有凸緣拉深件的高度取決勝于上模行程,模具中要設計有限程器,以便于模具調整。
4) 對稱工件的模架要明顯不對稱,以防止上、下模位置裝錯,非旋轉工件的凸、凹模裝配位置必須準確可行,發防松動后發生旋轉,偏移而影響工件質量,甚至損壞模具。
5) 對于形狀復雜,需經過多次拉深的零件,需先做拉深模,經試壓確定合適的毛坯形狀和尺寸后再做落料模,并在拉深模上按已定形的毛坯,設計安裝定位裝置。
4
XX學院 畢業設計論文
摘要
隨著中國工業不斷地發展,模具行業也顯得越來越重要。本次畢業設計的任務是蓋冒墊片沖壓工藝分析和模具的具體結構設計。通過查閱了相關文獻資料,對接觸片零件進行工藝性分析,選擇并確定符合于給定條件的最優工藝方案,及進行了工藝與設計的有關計算,如:選擇基本工序,確定其順序、工序數目及工序組合形式。介紹了主要零部件的設計理念,詳細剖析了設計過程中一些思路,以及某些非標準零件的使用特點。闡述了復合模的設計要點, 使產品質量達到設計要求。然后以此為基礎,設計出沖壓模具主要零件的結構。并在設計中,介紹了零件的排樣圖、定位設計、沖裁力的計算和壓力中心的計算。
關鍵詞:蓋冒墊片 模具設計 復合模 沖壓工藝
With the continuous development of Chinese industry, the mold industry has become increasingly important. The graduation project's mission is to take cover gasket stamping process analysis and design of the specific structure of the mold. By consulting the relevant literature, parts of the contact plate process analysis, selection and determine the conditions found at the given optimum solution, and carried out the calculation and design process, such as: choice of basic processes, determine their order, the number of processes and process combinations. Introduced the main components of the design concept, detailed analysis of the design process, some ideas, and some non-standard parts to use features. Describes the design features of the composite model, so the product quality to meet the design requirements. Then this basis, design the structure of the major parts stamping die. And in the design, the layout of parts described map, locate the design, calculation and blanking force center of pressure calculations..
Keywords: Take cover gasket Mold Design Compound Die Stamping process
目錄
1緒論 5
1.緒論 1
1.1沖壓的概念、特點及應用 1
1.2沖壓的基本工序及模具 2
1.3沖壓技術的現狀及發展方向 3
2.工件工藝性分析 10
2.1拉深工藝及拉深模有設計 10
2.2有凸緣圓筒形件的拉深方法及工藝計算 11
2.3寬凸緣圓筒形件的工藝計算要點 12
2.4拉深凸模和凹模的間隙 13
2.5拉深凸模,凹模的尺寸及公差 13
2.6凹模圓角半徑 15
2.7凸模圓角半徑 15
3.沖裁工藝及沖裁模具的設計 17
3.1凸模與凹模刃口尺寸的計算 17
3.2凸、凹模刃口尺寸的計算方法 17
3.2.1落料 18
3.2.2沖孔 19
3.2.3凹模洞的類形 19
3.2.4凹模的外形尺寸 19
4.模具的其它零件 22
4.1模架 22
4.2模柄 23
4.3卸料板 24
4.4彈頂和推出裝置 25
4.5導向裝置(導柱 導套) 25
4.6固定零件(固定板、墊板) 27
4.7連接零件 27
5.主要組件的裝配 30
6.模具的工作過程 30
體會 33
參考文獻 35
3
第 26 頁 共 27 頁
e pos 模具工業現狀Process simulation in stamping – recent
applications for product and process design
Abstract
Process simulation for product and process design is currently being practiced in industry. However, a number of input variables have a significant effect on the accuracy and reliability of computer predictions. A study was conducted to evaluate the capability of FE-simulations for predicting part characteristics and process conditions in forming complex-shaped, industrial parts.
In industrial applications, there are two objectives for conducting FE-simulations of the stamping process; (1) to optimize the product design by analyzing formability at the product design stage and (2) to reduce the tryout time and cost in process design by predicting the deformation process in advance during the die design stage. For each of these objectives, two kinds of FE-simulations are applied. Pam-Stamp, an incremental dynamic-explicit FEM code released by Engineering Systems Int'l, matches the second objective well because it can deal with most of the practical stamping parameters. FAST_FORM3D, a one-step FEM code released by Forming Technologies, matches the first objective because it only requires the part geometry and not the complex process information.
In a previous study, these two FE codes were applied to complex-shaped parts used in manufacturing automobiles and construction machinery. Their capabilities in predicting formability issues in stamping were evaluated. This paper reviews the results of this study and summarizes the recommended procedures for obtaining accurate and reliable results from FE simulations.
In another study, the effect of controlling the blank holder force (BHF) during the deep drawing of hemispherical, dome-bottomed cups was investigated. The standard automotive aluminum-killed, drawing-quality (AKDQ) steel was used as well as high performance materials such as high strength steel, bake hard steel, and aluminum 6111. It was determined that varying the BHF as a function of stroke improved the strain distributions in the domed cups.
Keywords: Stamping; Process ;stimulation; Process design
1. Introduction
The design process of complex shaped sheet metal stampings such as automotive panels, consists of many stages of decision making and is a very expensive and time consuming process. Currently in industry, many engineering decisions are made based on the knowledge of experienced personnel and these decisions are typically validated during the soft tooling and prototyping stage and during hard die tryouts. Very often the soft and hard tools must be reworked or even redesigned and remanufactured to provide parts with acceptable levels of quality.
The best case scenario would consist of the process outlined in Fig. 1. In this design process, the experienced product designer would have immediate feedback using a specially design software called one-step FEM to estimate the formability of their design. This would allow the product designer to make necessary changes up front as opposed to down the line after expensive tooling has been manufactured. One-step FEM is particularly suited for product analysis since it does not require binder, addendum, or even most process conditions. Typically this information is not available during the product design phase. One-step FEM is also easy to use and computationally fast, which allows the designer to play “what if” without much time investment.
Fig. 1. Proposed design process for sheet metal stampings.
Once the product has been designed and validated, the development project would enter the “time zero” phase and be passed onto the die designer. The die designer would validate his/her design with an incremental FEM code and make necessary design changes and perhaps even optimize the process parameters to ensure not just minimum acceptability of part quality, but maximum achievable quality. This increases product quality but also increase process robustness. Incremental FEM is particularly suited for die design analysis since it does require binder, addendum, and process conditions which are either known during die design or desired to be known.
The validated die design would then be manufactured directly into the hard production tooling and be validated with physical tryouts during which the prototype parts would be made. Tryout time should be decreased due to the earlier numerical validations. Redesign and remanufacturing of the tooling due to unforeseen forming problems should be a thing of the past. The decrease in tryout time and elimination of redesign/remanufacturing should more than make up for the time used to numerically validate the part, die, and process.
Optimization of the stamping process is also of great importance to producers of sheet stampings. By modestly increasing one's investment in presses, equipment, and tooling used in sheet forming, one may increase one's control over the stamping process tremendously. It has been well documented that blank holder force is one of the most sensitive process parameters in sheet forming and therefore can be used to precisely control the deformation process.
By controlling the blank holder force as a function of press stroke AND position around the binder periphery, one can improve the strain distribution of the panel providing increased panel strength and stiffness, reduced springback and residual stresses, increased product quality and process robustness. An inexpensive, but industrial quality system is currently being developed at the ERC/NSM using a combination of hydraulics and nitrogen and is shown in Fig. 2. Using BHF control can also allow engineers to design more aggressive panels to take advantage the increased formability window provided by BHF control.
Fig. 2. Blank holder force control system and tooling being developed at the ERC/NSM labs.
Three separate studies were undertaken to study the various stages of the design process. The next section describes a study of the product design phase in which the one-step FEM code FAST_FORM3D (Forming Technologies) was validated with a laboratory and industrial part and used to predict optimal blank shapes. Section 4 summarizes a study of the die design stage in which an actual industrial panel was used to validate the incremental FEM code Pam-Stamp (Engineering Systems Int'l). Section 5 covers a laboratory study of the effect of blank holder force control on the strain distributions in deep drawn, hemispherical, dome-bottomed cups.
2. Product simulation – applications
The objective of this investigation was to validate FAST_FORM3D, to determine FAST_FORM3D's blank shape prediction capability, and to determine how one-step FEM can be implemented into the product design process. Forming Technologies has provided their one-step FEM code FAST_FORM3D and training to the ERC/NSM for the purpose of benchmarking and research. FAST_FORM3D does not simulate the deformation history. Instead it projects the final part geometry onto a flat plane or developable surface and repositions the nodes and elements until a minimum energy state is reached. This process is computationally faster than incremental simulations like Pam-Stamp, but also makes more assumptions. FAST_FORM3D can evaluate formability and estimate optimal blank geometries and is a strong tool for product designers due to its speed and ease of use particularly during the stage when the die geometry is not available.
In order to validate FAST_FORM3D, we compared its blank shape prediction with analytical blank shape prediction methods. The part geometry used was a 5?in. deep 12?in. by 15?in. rectangular pan with a 1?in. flange as shown in Fig. 3. Table 1 lists the process conditions used. Romanovski's empirical blank shape method and the slip line field method was used to predict blank shapes for this part which are shown in Fig. 4.
Fig. 3. Rectangular pan geometry used for FAST_FORM3D validation.
Table 1. Process parameters used for FAST_FORM3D rectangular pan validation
Fig. 4. Blank shape design for rectangular pans using hand calculations.
(a) Romanovski's empirical method; (b) slip line field analytical method.
Fig. 5(a) shows the predicted blank geometries from the Romanovski method, slip line field method, and FAST_FORM3D. The blank shapes agree in the corner area, but differ greatly in the side regions. Fig. 5(b)–(c) show the draw-in pattern after the drawing process of the rectangular pan as simulated by Pam-Stamp for each of the predicted blank shapes. The draw-in patterns for all three rectangular pans matched in the corners regions quite well. The slip line field method, though, did not achieve the objective 1?in. flange in the side region, while the Romanovski and FAST_FORM3D methods achieved the 1?in. flange in the side regions relatively well. Further, only the FAST_FORM3D blank agrees in the corner/side transition regions. Moreover, the FAST_FORM3D blank has a better strain distribution and lower peak strain than Romanovski as can be seen in Fig. 6.
Fig. 5. Various blank shape predictions and Pam-Stamp simulation results for the rectangular pan.
(a) Three predicted blank shapes; (b) deformed slip line field blank; (c) deformed Romanovski blank; (d) deformed FAST_FORM3D blank.
Fig. 6. Comparison of strain distribution of various blank shapes using Pam-Stamp for the rectangular pan.
(a) Deformed Romanovski blank; (b) deformed FAST_FORM3D blank.
To continue this validation study, an industrial part from the Komatsu Ltd. was chosen and is shown in Fig. 7(a). We predicted an optimal blank geometry with FAST_FORM3D and compared it with the experimentally developed blank shape as shown in Fig. 7(b). As seen, the blanks are similar but have some differences.
Fig. 7. FAST_FORM3D simulation results for instrument cover validation.
(a) FAST_FORM3D's formability evaluation; (b) comparison of predicted and experimental blank geometries.
Next we simulated the stamping of the FAST_FORM3D blank and the experimental blank using Pam-Stamp. We compared both predicted geometries to the nominal CAD geometry (Fig. 8) and found that the FAST_FORM3D geometry was much more accurate. A nice feature of FAST_FORM3D is that it can show a “failure” contour plot of the part with respect to a failure limit curve which is shown in Fig. 7(a). In conclusion, FAST_FORM3D was successful at predicting optimal blank shapes for a laboratory and industrial parts. This indicates that FAST_FORM3D can be successfully used to assess formability issues of product designs. In the case of the instrument cover, many hours of trial and error experimentation could have been eliminated by using FAST_FORM3D and a better blank shape could have been developed.
Fig. 8. Comparison of FAST_FORM3D and experimental blank shapes for the instrument cover.
(a) Experimentally developed blank shape and the nominal CAD geometry; (b) FAST_FORM3D optimal blank shape and the nominal CAD geometry.
3. Die and process simulation – applications
In order to study the die design process closely, a cooperative study was conducted by Komatsu Ltd. of Japan and the ERC/NSM. A production panel with forming problems was chosen by Komatsu. This panel was the excavator's cabin, left-hand inner panel shown in Fig. 9. The geometry was simplified into an experimental laboratory die, while maintaining the main features of the panel. Experiments were conducted at Komatsu using the process conditions shown in Table 2. A forming limit diagram (FLD) was developed for the drawing-quality steel using dome tests and a vision strain measurement system and is shown in Fig. 10. Three blank holder forces (10, 30, and 50?ton) were used in the experiments to determine its effect. Incremental simulations of each experimental condition was conducted at the ERC/NSM using Pam-Stamp.
Fig. 9. Actual product – cabin inner panel.
Table 2. Process conditions for the cabin inner investigation
Fig. 10. Forming limit diagram for the drawing-quality steel used in the cabin inner investigation.
At 10?ton, wrinkling occurred in the experimental parts as shown in Fig. 11. At 30?ton, the wrinkling was eliminated as shown in Fig. 12. These experimental observations were predicted with Pam-stamp simulations as shown in Fig. 13. The 30?ton panel was measured to determine the material draw-in pattern. These measurements are compared with the predicted material draw-in in Fig. 14. Agreement was very good, with a maximum error of only 10?mm. A slight neck was observed in the 30?ton panel as shown in Fig. 13. At 50?ton, an obvious fracture occurred in the panel.
Fig. 11. Wrinkling in laboratory cabin inner panel, BHF=10?ton.
Fig. 12. Deformation stages of the laboratory cabin inner and necking, BHF=30?ton.
(a) Experimental blank; (b) experimental panel, 60% formed; (c) experimental panel, fully formed; (d) experimental panel, necking detail.
Fig. 13. Predication and elimination of wrinkling in the laboratory cabin inner.
(a) Predicted geometry, BHF=10?ton; (b) predicted geometry, BHF=30?ton.
Fig. 14. Comparison of predicted and measured material draw-in for lab cabin inner, BHF=30?ton.
Strains were measured with the vision strain measurement system for each panel, and the results are shown in Fig. 15. The predicted strains from FEM simulations for each panel are shown in Fig. 16. The predictions and measurements agree well regarding the strain distributions, but differ slightly on the effect of BHF. Although the trends are represented, the BHF tends to effect the strains in a more localized manner in the simulations when compared to the measurements. Nevertheless, these strain prediction show that Pam-Stamp correctly predicted the necking and fracture which occurs at 30 and 50?ton. The effect of friction on strain distribution was also investigated with simulations and is shown in Fig. 17.
Fig. 15. Experimental strain measurements for the laboratory cabin inner.
(a) measured strain, BHF=10?ton (panel wrinkled); (b) measured strain, BHF=30?ton (panel necked); (c) measured strain, BHF =50?ton (panel fractured).
Fig. 16. FEM strain predictions for the laboratory cabin inner.
(a) Predicted strain, BHF=10?ton; (b) predicted strain, BHF=30?ton; (c) predicted strain, BHF=50?ton.
Fig. 17. Predicted effect of friction for the laboratory cabin inner, BHF=30?ton.
(a) Predicted strain, μ=0.06; (b) predicted strain, μ=0.10.
A summary of the results of the comparisons is included in Table 3. This table shows that the simulations predicted the experimental observations at least as well as the strain measurement system at each of the experimental conditions. This indicates that Pam-Stamp can be used to assess formability issues associated with the die design.
Table 3. Summary results of cabin inner study
4. Blank holder force control – applications
The objective of this investigation was to determine the drawability of various, high performance materials using a hemispherical, dome-bottomed, deep drawn cup (see Fig. 18) and to investigate various time variable blank holder force profiles. The materials that were investigated included AKDQ steel, high strength steel, bake hard steel, and aluminum 6111 (see Table 4). Tensile tests were performed on these materials to determine flow stress and anisotropy characteristics for analysis and for input into the simulations (see Fig. 19 and Table 5).
Fig. 18. Dome cup tooling geometry.
Table 4. Material used for the dome cup study
Fig. 19. Results of tensile tests of aluminum 6111, AKDQ, high strength, and bake hard steels.
(a) Fractured tensile specimens; (b) Stress/strain curves.
Table 5. Tensile test data for aluminum 6111, AKDQ, high strength, and bake hard steels
It is interesting to note that the flow stress curves for bake hard steel and AKDQ steel were very similar except for a 5% reduction in elongation for bake hard. Although, the elongations for high strength steel and aluminum 6111 were similar, the n-value for aluminum 6111 was twice as large. Also, the r-value for AKDQ was much bigger than 1, while bake hard was nearly 1, and aluminum 6111 was much less than 1.
The time variable BHF profiles used in this investigation included constant, linearly decreasing, and pulsating (see Fig. 20). The experimental conditions for AKDQ steel were simulated using the incremental code Pam-Stamp. Examples of wrinkled, fractured, and good laboratory cups are shown in Fig. 21 as well as an image of a simulated wrinkled cup.
Fig. 20. BHF time-profiles used for the dome cup study.
(a) Constant BHF; (b) ramp BHF; (c) pulsating BHF.
Fig. 21. Experimental and simulated dome cups.
(a) Experimental good cup; (b) experimental fractured cup; (c) experimental wrinkled cup; (d) simulated wrinkled cup.
Limits of drawability were experimentally investigated using constant BHF. The results of this study are shown in Table 6. This table indicates that AKDQ had the largest drawability window while aluminum had the smallest and bake hard and high strength steels were in the middle. The strain distributions for constant, ramp, and pulsating BHF are compared experimentally in Fig. 22 and are compared with simulations in Fig. 23 for AKDQ. In both simulations and experiments, it was found that the ramp BHF trajectory improved the strain distribution the best. Not only were peak strains reduced by up to 5% thereby reducing the possibility of fracture, but low strain regions were increased. This improvement in strain distribution can increase product stiffness and strength, decrease springback and residual stresses, increase product quality and process robustness.
Table 6. Limits of drawability for dome cup with constant BHF
Fig. 22. Experimental effect of time variable BHF on engineering strain in an AKDQ steel dome cup.
Fig. 23. Simulated effect of time variable BHF on true strain in an AKDQ steel dome cup.
Pulsating BHF, at the frequency range investigated, was not found to have an effect on strain distribution. This was likely due to the fact the frequency of pulsation that was tested was only 1?Hz. It is known from previous experiments of other researchers that proper frequencies range from 5 to 25?Hz [3]. A comparison of load-stroke curves from simulation and experiments are shown in Fig. 24 for AKDQ. Good agreement was found for the case where μ=0.08. This indicates that FEM simulations can be used to assess the formability improvements that can be obtained by using BHF control techniques.
Fig. 24. Comparison of experimental and simulated load-stroke curves for an AKDQ steel dome cup.
5 Conclusions and future work
In this paper, we evaluated an improved design process for complex stampings which involved eliminating the soft tooling phase and incorporated the validation of product and process using one-step and incremental FEM simulations. Also, process improvements were proposed consisting of the implementation of blank holder force control to increase product quality and process robustness.
Three separate investigations were summarized which analyzed various stages in the design process. First, the product design phase was investigated with a laboratory and industrial validation of the one-step FEM code FAST_FORM3D and its ability to assess formability issues involved in product design. FAST_FORM3D was successful at predicting optimal blank shapes for a rectangular pan and an industrial instrument cover. In the case of the instrument cover, many hours of trial and error experimentation could have been eliminated by using FAST_FORM3D and a better blank shape could have been developed.
Second, the die design