FSAE電動賽車前懸架結構設計與分析【雙橫臂式懸架優秀課程畢業設計含5張CAD圖紙帶任務書+開題報告+中期報告+答辯ppt+外文翻譯】-clsj24

FSAE電動賽車前懸架結構設計與分析【雙橫臂式懸架優秀課程畢業設計含5張CAD圖紙帶任務書+開題報告+中期報告+答辯ppt+外文翻譯】-clsj24

FSAE電動賽車前懸架結構設計與分析【雙橫臂式懸架】

摘要：本設計對FSAE賽車前懸架的結構及特點進行比較，綜合比對選取適合的懸架結構形式，最終確立FSAE電動賽車的前懸架采用雙橫臂式懸架結構；根據賽車參數，進行了大量的計算，根據數據確立了前懸架的尺寸，材料，以及懸架部件的選取以及參數，對影響安全性的零件，例如橫向穩定桿和緩沖塊都有明確的計算與設計，然后進行ADAMS建模、優化，最終確認主銷外傾角，主銷內傾角，均滿足設計要求。隨之選用 proe軟件對FSAE前懸架實施3D圖形的創造；在建立三維模型的過程中，根據零件的三維坐標，生成三維模型，這樣的精確度高。再后，使用有限元分析軟件ANSYS對整體結構進行靜態分析和動態分析，在靜態分析中，均符合設計要求，在動態分析中，著重對在0.5g加速狀態和0.95g轉彎狀態下進行有限元分析，前懸架下控制器在這兩種嚴格的工況下，所產生的應力集中問題，和應力變形問題，對這兩種問題進行分析比對，對應力集中現象，都小于材料的屈服極限，說明滿足安全的要求，對應力變形問題，也同樣滿足設計要求。本次FSAE賽車的前懸架完全符合設計要求。

關鍵詞：FSAE賽車；懸架；校核；有限元；

Design and Analysis of Front Suspension Structure

of FSAE Electric Racing

Abstract：This graduation design the structure and characteristics of FSAE car front suspension is used in the comparison, comprehensive than to choose a suitable suspension structure, finally established FSAE electric car front suspension with double wishbone type suspension structure;According to the parameters of car, a large amount of calculation, based on the size of the data to establish the front suspension, materials, and the selection of suspension components and parameters, affecting the safety of spare parts, such as the horizontal stabilizer bar and buffer blocks are clearly calculation and design, then, ADAMS, modeling, optimization and finally confirm the king pin camber Angle, kingpin inclination Angle, meet the design requirements.Then using proe FSAE car front suspension three-dimensional organization simulation model is set up;In the process of establishing three-dimensional model, according to the components of the three-dimensional coordinates, generated 3 d model, the precision is high.Again later, using the finite element analysis software ANSYS static analysis and dynamic analysis was carried out on the whole structure, in static analysis, all comply with the design requirements, in the dynamic analysis, the state of accelerating in 0.5 g and 0.95 g condition in finite element analysis of turning, the front controller in both the strict conditions, the stress concentration problems, and stress deformation problem, the analysis of the two kinds of problems, the stress concentration phenomenon, are less than the yield limit of material, that meet the requirements of safety, the deformation and stress problem, also meet the design requirements.The FSAE car front suspension fully comply with the design requirements.analysis controller.

Key words: FSAE racing; suspension; check; finite element;

目  錄

摘要……………………………………………………………….…………………... I

Abstract…………………………………………………………………...…………II

1.緒論……………………………………………………………….……………..….1

1.1國內研究現狀…………………………………………………….……………….1

1.2國外研究現狀…………………………………………………….…..………...…2

2. FSAE前懸架的建立………………………………………....………………..……3

2.1 FSAE 賽車懸架的選擇…………………………………...…………...…………3

2.2前懸架參數設計……………………………………..………...…………...……..4

2.2.1對平順性影響的各項參數……………………………………………………...4

2.2.2撓度計算………………………………………………………………………...5

2.2.3簧載質量與非簧載質量………………………………………………………...5

2.3螺旋彈簧的設計……………………....………………….………….………...….6

2.3.1螺旋彈簧類型的選擇…………………………………………………………...6

2.3.2彈簧的關計算…………………………………………………………………...7

2.3減振器設計……………………………………………………………………….10

2.3.1減振器及其形式的選擇……………………………………………………… .10

2.3.2相對阻尼系數……………………………….………………………………….11

2.3.3減振器阻尼系數的確定………………………………………………………..11

2.3.4最大卸荷力的確定………….………………………………………………….11

2.3.5減振器尺寸的確定……………………………………………………………..12

2.4上、下橫臂長度的確定………………………………………………………….12

2.5橫向穩定桿設計………………………...………………………………………..12

2.5.1穩定桿直徑計算………………………………………………………………..13

2.6緩沖塊…………………………………………………...……………………….14

3. 對FSAE的前懸架進行三維建模…………………….…….……………………15

3.1前懸架運動學參數的分析………………………………………...…..……...…17

4.控制臂的有限元分析………………………………..……..…………...…..….…20

4.1有限元法的介紹…………………………..………………………...…………...20

4.2控制臂有限元模型建立………………………….…………………..……….…20

4.2.1幾何模型……………………………….………………………………………20

4.2.2網格劃分及網格質量控制…………………………………………………….21

4.2.3材料屬性定義………………………………………………………………...22

4.2.4慣性釋放及模型的約束與加載……………………………………………...22

4.3典型極限工況控制臂結構有限元分析………………………………………...22

4.3.1 0.5g加速工況………………………………………………………………….22

4.3.2 0.95g轉向工況……………………………………………………………...…23

5.總結與展望…………………………………….….………..……………………..25

5.1總結…………………………………………….……………………...…………25

5.2展望…………………………………………….…………………………...……26

參考文獻…………………………………………….………………………….……27

致謝…………………………………………………..………………………………28

【詳情如下】【需要咨詢購買全套設計請加QQ1459919609】

FSAE電動賽車前懸架結構設計與分析.docx

FSAE電動賽車前懸架結構設計與分析任務書.doc

FSAE電動賽車前懸架結構設計與分析開題報告.doc

FSAE電動賽車前懸架結構設計與分析答辯ppt.pptx

上橫臂A1.dwg

下橫臂A1.dwg

前懸架推桿A2.dwg

雙橫臂前懸架裝配圖A0.dwg

外文翻譯.docx

文件清單.txt

立柱A1.dwg

FSAE電動賽車前懸架結構設計與分析