救援小車的設計含程序及CAD圖

救援小車的設計含程序及CAD圖,救援,救濟,營救,小車,設計,程序,cad 救援小車的設計 摘 要 自動循跡避障小車在工業和生產上都有廣泛運用，為了培養大學生對循跡避障的運用，循跡避障機器人最近幾年一直是各類全國大學生機電類比賽的主要題目。而本次題目要求小車能根據外部環境的變化而做出智能的判斷并成功執行題目要求的循跡、避障和發現目標的任務。 本設計采用單片機控制技術為核心，通過對各類傳感器的合理運用以達到設計要求。本系統主要由單片機、紅外傳感器、光電接近開關、直流電機、穩壓芯片組成。系統采用可充電電池作為總電源，并通過穩壓芯片進行穩壓分別對各部分電路進行供電。其中系統的數據采集部分采用5組紅外對管對地面信息進行數據收集，并且再利用兩組光電接近開關對障礙物進行數據的收集；然后將收集到的外部數據信息傳輸?shù)絾纹瑱C(jī)上根據程序進行相應的數據處理，從而使小車系統能準確、快速地采集處理外部環境信息并反饋到小車系統執行部分去。最后根據單片機對外部信息的處理結果對兩個直流電機進行控制從而實現小車根據外部環境自動進行循跡、避障、發現目標的操作；并通過單片機對蜂鳴器和LED的控制實現光電報警。 整個系統的電路機構簡單，可靠性好。并且本救援小車系統具有執行效率高、反應快速和低成本等優點。根據小車調試運行情況來說，本次設計能很好地根據外部環境的變化執行預定任務。 關鍵詞：救援小車；L298N；紅外對管；STC89C52；直流電機；光電開關 Abstract Automatic tracking obstacle avoidance for car industry and production, widely used, in order to develop the use of college students on the tracking of obstacle avoidance, tracking, obstacle avoidance robot in recent years has been the main subject of thevarious types of National College Students of machinery and electronic game. The subject car changes in the external environment and to make intelligent judgments andthe successful implementation of the subject requirements tracking, obstacle avoidance,and found the target task. This design uses a single-chip control technology as the core, through the rational use ofvarious types of sensors to meet the design requirements. The system mainly consists of the microcontroller, infrared sensors, photoelectric proximity switches, DC motors,voltage regulator chip. The system uses a rechargeable battery as the total power supplyvoltage regulator and the regulator chip on the part of the circuit power supply. The system includes data acquisition part of group of infrared tubes on the ground information data collection, and use of two sets of photoelectric proximity switch on the obstacles to data collection; then collected from the external data transmission to the MCU according to the procedures the corresponding data processing, so that the car system can accurately and quickly collecting and processing the external environment for information and feedback to the operative part to go to the car system. The last two DC motor control in order to achieve the car is automatically carried out according to theexternal environment, tracking, obstacle avoidance, found that the operation of the target;and photoelectric alarm buzzer and LED control by the microcontroller according to the results of single-chip processing of external information. Circuit body of the whole system is simple and good reliability. And the rescue vehicle system with high efficiency in the implementation, fast response and low cost advantages. For debugging and running under the car, the design changes in theexternal environment perform the intended task. Key words: Rescue car ; L298N; nfrared Emitting Diode ; STC89C52; DC motor ；Photoelectric switch